Activity Stream

Hi all Is disabling the EGR as simple as zeroing the tables under Exhaust > Gas Recircation? Thanks

i have a question ? does the pcm use the temp sensor to read the temp and if its to high and it sees the knock sensor voltage is at its normal range...

Now that it's official the big news that the 2024-2025 Mustangs can be tuned, I'm asking anyone who can to upload a readout so we can analyze the...

Hi guys Patient under surgery is 1997 Corvette. Stock internals, BBK shorty headers, race cats and Borla exhaust. Procharger P1SC low boost setup....

Ok fellas, I have heard about the itch you get after your first mod to your car but right now I wish I had never even scratched it. I bought this...

Hey all, any pros out there willing to share some of there channels and charts (xml?s). ive managed to pull a couple of log files(from various...

Good Morning. I finally got the engine in and on the road for the first drive today... Unfortunately the first drive was on the interstate for the 30...

Now that tuning is supported for the 24+ F-150, I will be posting a stock file soon and begin testing different setups. I will share results here as...

im getting knock around 72kpa @ 4000 to 4400 rpm from 3 to 8 . i cant hear no pinging at all. could my headers or exhaust pipe be rubbing some where...

have a 2007 ly5 with a fresh BTR cam (truck norris) and valvetrain, long tubes, otherwise stock. Fighting an extremely high idle issue. Engine...

Losing my marbles a tiny bit. I've been chasing my tail for quite a while now, and I think I must be missing something basic. I have a 4.8 with...

I made way more modifications to engine than I can tune, but it seems to be running decent. main issue is cruising at around 2k rpm I'm getting...

I am currently building a '68 GMC Suburban. I have a Gen IV 6.0LS and 6L80, using wiring harness from PSI. engine cranks but that is it. I have a ECU...

I wanted to share this project I made that will display the AFR on the dash as water depth. It also has a function to control heating of the sensor...

hi all , when i move my shifter over to manual mode i dont want the transmission to change down gears. if im in 4th at 3000rpm and put the foot to...

im hoping for some help going thru this tune to make sure things are correct. the car seems to be running lean according to the spark plugs. they...

**Update** Running 7/25/25 (spoiler, bad MAP sensor brand new out of the box) I'm adding a turbo and want to tune in the VE mode and eliminate the...

Hi, I'm new to all this so please be patient. My tuner has sent me the tune file for my vehicle so I can make some edits. I have downloaded the...

I recently replaced the engine in my 2016 Hyundai Veloster Turbo (MED17.9.8, OS ID GTFS-HFU6FS00H01) and now I’m running into what I believe is an...

Alright, I swapped in a "500HP" crate engine. Got it "professionally" tuned, to 304HP. All my logs look ok, obviously I'm no expert so who knows....

I bought a Jeep Wrangler with an LM7 5300 GM engine swap and I have an intermittent issue. CURRENT ISSUE: Most of the time no start (no fuel, I...

Howdy, I'm trying to figure out what the ECM uses for "in gear" and would like someone with an L67 car to log a quick drive with the PRNDL Status...

Hi guys, have a BA Falcon here NA+T 3584, kelford 218b cams, 1000cc injectors auto built btr with 3500rpm stall. Having issues getting it to idle...

Hello, I need help making a stage 1 tune for my car, it has a cold air intake and the rest is stock, with the EA113 2.0TFSI BPY engine with the...

Mistake #1. I ordered what I thought was a brp/can-am obd2 adapter on Amazon. Mistake #2. I then proceeded to plug my mpvi3 into my can am commander...

So, I did a read on my truck a few weeks ago using an older version of HPT, I haven't updated my software in a while. When I hooked up to the truck...

Can somone please share a stock 2014 rs sonic please thanks

Hi all, first post, first 6l80 rebuild and first HPTune. About 4000 miles ago I rebuilt the 6l80 in a '15 Yukon. She was doing great until just...

Can someone lead me in the right direction. I have done my due diligence with the search feature but unable to find specific answers. I am...

After a trashed cam replacement, I installed a TSP Stage 3 cam with phaser limiter. I replaced the lifters with Comp cam Non MDS and Did the delete...