Page 1004 of 1240 FirstFirst ... 4504904954994100010011002100310041005100610071008101410541104 ... LastLast
Threads 20061 to 20080 of 24786

Forum: GM V8 Tuning - Engine, Gas (Gen 3)

(1997-2009, LS1, LS6, ...)

  1. Sticky Thread Sticky: If you want us to help with a tune or scan issue post your .hpt file, log & .cfg too.

    Started by jimmyblue, 10-19-2009
    92 Attachment(s)
    • Replies: 0
    • Views: 106,711
    jimmyblue
    10-19-2009 Go to last post

  2. Sticky Thread Sticky: READ ME!!! General tuning info and how-to's

    Started by WS6FirebirdTA00, 02-07-2006
    • Replies: 0
    • Views: 290,561
    WS6FirebirdTA00
    02-07-2006 Go to last post

  1. is 40deg the max ls1 timing?

    Started by sikhabib, 04-26-2008
    • Replies: 8
    • Views: 5,327
    Bill@HPTuners
    05-14-2008 Go to last post

  2. Secondary VE question

    Started by KLUG'S SS, 05-12-2008
    • Replies: 6
    • Views: 2,941
    KLUG'S SS
    05-13-2008 Go to last post

  3. 5.3 swap in a 06 6cyl manual truck tack?

    Started by van383, 05-12-2008
    • Replies: 6
    • Views: 2,892
    van383
    05-13-2008 Go to last post

  4. RAF vs. IAC vs. Idle Spark

    Started by RZRSEDGE, 05-09-2008
    • Replies: 9
    • Views: 4,067
    RZRSEDGE
    05-13-2008 Go to last post

  5. Any benifits using 2 bar SD with a maggie

    Started by red99, 05-13-2008
    • Replies: 3
    • Views: 2,054
    MonkeyGod
    05-13-2008 Go to last post

  6. why is maf and stft still working?

    Started by PHASEMASTER1, 04-30-2008
    2 Pages •
    1 2
    • Replies: 30
    • Views: 12,021
    5_Liter_Eater
    05-13-2008 Go to last post

  7. 1999 30th TA: trouble with DTCs and reading PCM

    Started by SilverTurtle, 05-12-2008
    • Replies: 3
    • Views: 1,784
    SilverTurtle
    05-12-2008 Go to last post

  8. 06 Hummer MPG Config File???

    Started by sikgmc, 05-12-2008
    • Replies: 0
    • Views: 1,298
    sikgmc
    05-12-2008 Go to last post

  9. Idle surge only if AC is OFF

    Started by rel3rd, 05-08-2008
    • Replies: 4
    • Views: 2,483
    WS6FirebirdTA00
    05-12-2008 Go to last post

  10. wont run in open loop

    Started by edcmat-l1, 05-09-2008
    • Replies: 19
    • Views: 7,088
    edcmat-l1
    05-12-2008 Go to last post

  11. I want to log the IAT Timing pulled.

    Started by Chuckster, 05-11-2008
    • Replies: 6
    • Views: 2,908
    Gh0st
    05-12-2008 Go to last post

  12. Reprogram to Flex fuel?

    Started by tahoe, 05-03-2008
    • Replies: 13
    • Views: 9,158
    tahoe
    05-11-2008 Go to last post

  13. Sd Tuned/snow Meth Controller (maf)

    Started by anarchy99, 01-29-2007
    • Replies: 2
    • Views: 1,756
    LS1408
    05-10-2008 Go to last post

  14. Fast 90 Install. Looking for a review.

    Started by 97SilverC5, 04-29-2008
    2 Pages •
    1 2
    • Replies: 24
    • Views: 10,386
    97SilverC5
    05-10-2008 Go to last post

  15. Newbie to this, few issues - could use direction

    Started by MeanYellowZ, 05-09-2008
    • Replies: 1
    • Views: 1,237
    LinearX
    05-10-2008 Go to last post

  16. Some Idle Proplem

    Started by The devil, 05-09-2008
    • Replies: 5
    • Views: 2,631
    R32WA
    05-10-2008 Go to last post

  17. VE Tuning Confusion

    Started by Gh0st, 05-06-2008
    • Replies: 10
    • Views: 3,852
    Rhino
    05-09-2008 Go to last post

  18. Tuned by Wideband...now LTFT = +4

    Started by ChrisV 02 - Z28, 05-09-2008
    • Replies: 0
    • Views: 1,187
    ChrisV 02 - Z28
    05-09-2008 Go to last post

  19. Exclamation How do you really dial the RAF in?

    Started by Billiumss, 09-28-2006
    • Replies: 19
    • Views: 8,547
    5_Liter_Eater
    05-09-2008 Go to last post

  20. Running very lean on cold starts - log attached

    Started by Gh0st, 05-07-2008
    • Replies: 9
    • Views: 3,733
    WS6FirebirdTA00
    05-09-2008 Go to last post
Page 1004 of 1240 FirstFirst ... 4504904954994100010011002100310041005100610071008101410541104 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.