Page 1008 of 1238 FirstFirst ... 8508908958998100410051006100710081009101010111012101810581108 ... LastLast
Threads 20141 to 20160 of 24760

Forum: GM V8 Tuning - Engine, Gas (Gen 3)

(1997-2009, LS1, LS6, ...)

  1. Sticky Thread Sticky: If you want us to help with a tune or scan issue post your .hpt file, log & .cfg too.

    Started by jimmyblue, 10-19-2009
    92 Attachment(s)
    • Replies: 0
    • Views: 106,134
    jimmyblue
    10-19-2009 Go to last post

  2. Sticky Thread Sticky: READ ME!!! General tuning info and how-to's

    Started by WS6FirebirdTA00, 02-07-2006
    • Replies: 0
    • Views: 289,839
    WS6FirebirdTA00
    02-07-2006 Go to last post

  1. 408 l92 l76

    Started by project nightmare, 04-20-2008
    • Replies: 4
    • Views: 2,391
    BTLD_LS1
    04-21-2008 Go to last post

  2. "vacuum" kpa different than kPa?

    Started by Wilde Racing, 04-20-2008
    • Replies: 9
    • Views: 8,479
    Wilde Racing
    04-21-2008 Go to last post

  3. nitrous log

    Started by BTLD_LS1, 04-21-2008
    • Replies: 0
    • Views: 1,155
    BTLD_LS1
    04-21-2008 Go to last post

  4. SD tuning Running rich Question.

    Started by maxgee, 04-20-2008
    • Replies: 1
    • Views: 1,381
    EC_Tune
    04-21-2008 Go to last post

  5. Unusual Lean Spots

    Started by mikeyv, 04-20-2008
    • Replies: 5
    • Views: 2,313
    EC_Tune
    04-20-2008 Go to last post

  6. MAF gone, cranking issues now

    Started by swampnuts, 04-19-2008
    • Replies: 1
    • Views: 1,483
    EC_Tune
    04-20-2008 Go to last post

  7. VCM with Superchips

    Started by HerronPerformance, 04-20-2008
    • Replies: 1
    • Views: 1,573
    EC_Tune
    04-20-2008 Go to last post

  8. Knock Retard Problem

    Started by Blown06, 04-19-2008
    • Replies: 2
    • Views: 1,795
    EC_Tune
    04-20-2008 Go to last post

  9. If in open loop does proportional fueling still have any say in fuel delivery?

    Started by mike01z, 04-08-2008
    • Replies: 6
    • Views: 2,662
    EC_Tune
    04-20-2008 Go to last post

  10. puzzled with PE AF values..........

    Started by ccrp, 04-19-2008
    • Replies: 2
    • Views: 1,635
    ccrp
    04-20-2008 Go to last post

  11. bin file for STS tune? Anyone

    Started by bin_ajail, 04-02-2008
    • Replies: 4
    • Views: 2,764
    bin_ajail
    04-20-2008 Go to last post

  12. When tuning for open loop idle don't trust closed loop status bit.

    Started by mike01z, 04-19-2008
    • Replies: 3
    • Views: 2,032
    mike01z
    04-19-2008 Go to last post

  13. For VE or MAF how much can closed loop sway a/f?

    Started by mike01z, 04-14-2008
    • Replies: 5
    • Views: 2,449
    mike01z
    04-19-2008 Go to last post

  14. Set for PE at 0 to 1200 rpm, yet never get closed loop. why? log and scan inside.

    Started by mike01z, 04-18-2008
    • Replies: 4
    • Views: 2,149
    mike01z
    04-19-2008 Go to last post

  15. Red face Just swapped flywheels to a lighter one where do I start?

    Started by The Alchemist, 04-14-2008
    • Replies: 14
    • Views: 6,108
    The Alchemist
    04-19-2008 Go to last post

  16. Trims + KR Issues

    Started by muayyadf1, 04-11-2008
    2 Pages •
    1 2
    • Replies: 21
    • Views: 6,980
    muayyadf1
    04-18-2008 Go to last post

  17. Inj. Pulse Width Drop

    Started by cartman003, 04-14-2008
    • Replies: 4
    • Views: 3,191
    EC_Tune
    04-18-2008 Go to last post

  18. Tune attached, suggestions and opinions

    Started by 1st-BAD-LS1, 04-14-2008
    • Replies: 4
    • Views: 2,027
    EC_Tune
    04-18-2008 Go to last post

  19. Tuning with Wideband 02

    Started by maxgee, 04-17-2008
    • Replies: 1
    • Views: 1,303
    EC_Tune
    04-18-2008 Go to last post

  20. Can Someone explain this?

    Started by Blue-Z, 04-15-2008
    • Replies: 9
    • Views: 4,057
    Blue-Z
    04-17-2008 Go to last post
Page 1008 of 1238 FirstFirst ... 8508908958998100410051006100710081009101010111012101810581108 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.