Page 1 of 125 123451151101 ... LastLast
Threads 1 to 20 of 2482

Forum: Dodge Tuning - Engine, Gas

  1. Sticky Thread Sticky: Dodge/Chrysler/Jeep VCM Suite 3.0+ Vehicle Supported List

    Started by Mark@HPTuners, 11-17-2014
    8 Pages
    1 2 3 ... 8
    • Replies: 157
    • Views: 109,747
    07-19-2019 Go to last post
  2. Sticky Thread Sticky: Dodge Viper Gen3 (JTEC/JTEC+) and Gen4 (Venom) tuning

    Started by Keith@HPTuners, 02-17-2014
    5 Pages
    1 2 3 ... 5
    • Replies: 80
    • Views: 56,519
    07-10-2019 Go to last post
  3. Sticky Thread Sticky: Dodge Viper Gen4 & Gen5 (Venom) available in 3.0+

    Started by Keith@HPTuners, 05-13-2014
    6 Pages
    1 2 3 ... 6
    • Replies: 109
    • Views: 77,707
    02-18-2019 Go to last post
  4. Thumbs up Sticky Thread Sticky: VCM Suite 3.2 - New Dodge Vehicle Controls & Special Functions

    Started by Mark@HPTuners, 06-20-2016
    4 Pages
    1 2 3 ... 4
    • Replies: 68
    • Views: 48,231
    08-17-2018 Go to last post
    • Replies: 7
    • Views: 27,546
    11-08-2016 Go to last post
    • Replies: 0
    • Views: 64,610
    04-16-2015 Go to last post
  1. No lift shift

    Started by Homer, 2 Days Ago
    • Replies: 7
    • Views: 116
    11 Minutes Ago Go to last post
  2. MDS delete on 2014 Ram2500

    Started by Paul3025, 5 Hours Ago
    • Replies: 2
    • Views: 25
    2 Hours Ago Go to last post
  3. 2018 jeep jl tune

    Started by Alshuwaihi, 07-20-2018
    • Replies: 3
    • Views: 804
    6 Hours Ago Go to last post
  4. No torque management

    Started by Jailhousecustoms112, 4 Weeks Ago
    3 Pages
    1 2 3
    • Replies: 40
    • Views: 1,117
    7 Hours Ago Go to last post
  5. check this crap out

    Started by ShannonSRT, 1 Week Ago
    • Replies: 13
    • Views: 253
    9 Hours Ago Go to last post
    • Replies: 1
    • Views: 46
    9 Hours Ago Go to last post
  6. FAIL during writing

    Started by piffo, 1 Day Ago
    • Replies: 1
    • Views: 41
    9 Hours Ago Go to last post
  7. Question Supercharged 5.7 with 6.2 cam

    Started by Homer, 4 Weeks Ago
    2 Pages
    1 2
    • Replies: 31
    • Views: 548
    1 Day Ago Go to last post
    • Replies: 3
    • Views: 141
    1 Day Ago Go to last post
  8. Swap from charger 5.7 to 6.4

    Started by WELLWELL, 1 Day Ago
    • Replies: 3
    • Views: 74
    1 Day Ago Go to last post
    • Replies: 0
    • Views: 35
    2 Days Ago Go to last post
    • Replies: 3
    • Views: 1,045
    2 Days Ago Go to last post
    • Replies: 17
    • Views: 640
    2 Days Ago Go to last post
  9. Viper MAP sensor scaling

    Started by aNinjaneer, 12-17-2014
    • Replies: 6
    • Views: 2,692
    2 Days Ago Go to last post
  10. 3.7-4.7 rom/throttle "hang"

    Started by MAIDENCR, 4 Days Ago
    • Replies: 4
    • Views: 84
    3 Days Ago Go to last post
  11. Kenne Bell 168mm voltage issue

    Started by R3nciukas, 08-08-2019
    • Replies: 3
    • Views: 130
    3 Days Ago Go to last post
  12. HP Tuners Now Offering JTEC Support!

    Started by Darek@HPTuners, 2 Weeks Ago
    3 Pages
    1 2 3
    • Replies: 52
    • Views: 2,080
    4 Days Ago Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.