Page 11 of 880 FirstFirst ... 7891011121314152161111511 ... LastLast
Threads 201 to 220 of 17583

Forum: GM V8 Tuning - Engine, Gas (Gen 4)

(2005-2015, LS2, LS7, ...)

  1. Sticky Thread Sticky: Read Me!!! Tuning How-To's & General Information

    Started by Bill@HPTuners, 01-06-2007
    3 Pages •
    1 2 3
    3 Attachment(s)
    • Replies: 44
    • Views: 387,197
    blindsquirrel
    04-14-2025 Go to last post

  1. Dies at idle after a couple minutes

    Started by jlamp67, 04-13-2025
    7 Attachment(s)
    • Replies: 14
    • Views: 1,204
    edcmat-l1
    04-15-2025 Go to last post

  2. I want my LS7 to CHOP

    Started by Jacobm832, 04-11-2021
    1 Attachment(s)
    • Replies: 12
    • Views: 4,420
    Speedboosted
    04-15-2025 Go to last post

  3. Stoich, IFR and IVT scaling spreadsheet.

    Started by mcfarlnd, 07-11-2020
    • Replies: 1
    • Views: 2,233
    cjmelcher
    04-14-2025 Go to last post

  4. E38 issues to avoid, VSS issues and throttle TAC issues, incompatibility

    Started by trbo355, 04-30-2015
    2 Attachment(s)
    • Replies: 15
    • Views: 15,180
    blindsquirrel
    04-13-2025 Go to last post

  5. 6.2 to 5.3 swap questions

    Started by Thatoneoldguy, 04-07-2025
    • Replies: 9
    • Views: 684
    Thatoneoldguy
    04-13-2025 Go to last post

  6. No Lift Shift 2010 Camaro ss

    Started by Camaro352, 04-09-2025
    1 Attachment(s)
    • Replies: 5
    • Views: 580
    Camaro352
    04-13-2025 Go to last post

  7. 09 silverado 5.3 truck norris tuning help

    Started by kurt.reeder88, 04-10-2025
    3 Attachment(s)
    • Replies: 5
    • Views: 497
    Xguardian
    04-13-2025 Go to last post

  8. Intermittent - 6L80 Issue: Current Gear vs Gear Selector Position

    Started by dromey, 04-04-2025
    • Replies: 1
    • Views: 373
    dromey
    04-13-2025 Go to last post

  9. Newb looking for assist with tuning

    Started by adamcfla, 04-11-2025
    • Replies: 13
    • Views: 575
    biholliday
    04-13-2025 Go to last post

  10. E38 compatible with 6l80?? (originally had 4l65)

    Started by Kiwiguy, 04-09-2025
    2 Attachment(s)
    • Replies: 15
    • Views: 598
    blindsquirrel
    04-13-2025 Go to last post

  11. is someone able to tell me if my torque converter is bad?

    Started by radeon1337, 04-12-2025
    • Replies: 2
    • Views: 599
    radeon1337
    04-12-2025 Go to last post

  12. Anyone had experience tuning Granetelli DBW on Gen4 G8 etc? Scalar?

    Started by GrannySShifting, 04-10-2025
    2 Attachment(s)
    • Replies: 12
    • Views: 998
    Alvin
    04-12-2025 Go to last post

  13. Cam sensor issues, wiring, or wrong reluctor wheel can cause a VATS like no start

    Started by Alvin, 04-04-2025
    3 Attachment(s)
    • Replies: 5
    • Views: 1,993
    blindsquirrel
    04-12-2025 Go to last post

  14. Quick guide to simultaneous VVE/MAF calibration for gen4+

    Started by smokeshow, 07-06-2020
    12 Pages •
    1 2 3 ... 12
    29 Attachment(s)
    • Replies: 222
    • Views: 167,802
    smokeshow
    04-12-2025 Go to last post

  15. Need to program brand new dealer e67 for 07 trailblazer ss

    Started by [email protected], 04-06-2025
    2 Pages •
    1 2
    1 Attachment(s)
    • Replies: 23
    • Views: 823
    Alvin
    04-11-2025 Go to last post

  16. sanity check please. feel like something isnt right.

    Started by Millspecauto, 03-23-2025
    2 Attachment(s)
    • Replies: 5
    • Views: 577
    Millspecauto
    04-10-2025 Go to last post

  17. 2008 6L80e high power 2-3 WOt shift

    Started by MoBoost, 04-08-2025
    2 Attachment(s)
    • Replies: 3
    • Views: 255
    MoBoost
    04-09-2025 Go to last post

  18. Disable "Reduced Engine Power" E38

    Started by 8aHemi, 03-08-2025
    • Replies: 1
    • Views: 426
    RoninDusette
    04-09-2025 Go to last post

  19. [HELP] Crank-No-Start After ECM Swap and Tune ? Fuel Pump Command 99% But No Prime

    Started by navedj786, 04-08-2025
    1 Attachment(s)
    • Replies: 4
    • Views: 372
    RoninDusette
    04-09-2025 Go to last post

  20. Sudden drop in G/Cyl for no reason

    Started by CK@UPP, 06-12-2018
    2 Attachment(s)
    • Replies: 12
    • Views: 4,006
    Cringer
    04-08-2025 Go to last post
Page 11 of 880 FirstFirst ... 7891011121314152161111511 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.