Page 5 of 138 FirstFirst 1234567891555105 ... LastLast
Threads 81 to 100 of 2753

Forum: VCM Editor

General product use: Editing, Flashing, ...

  1. Sticky Thread Sticky: Tunerlocking in VCM Suite 3.0+

    Started by Mark@HPTuners, 02-29-2016
    3 Attachment(s)
    • Replies: 0
    • Views: 27,207
    Mark@HPTuners
    02-29-2016 Go to last post

  2. Sticky Thread Sticky: Remote Tuning - Master/Slave MPVI VCM Suite 3.0

    Started by Mark@HPTuners, 03-03-2016
    3 Attachment(s)
    • Replies: 0
    • Views: 24,235
    Mark@HPTuners
    03-03-2016 Go to last post

  3. Sticky Thread Sticky: VCM Editor Feature - User Defined Parameters

    Started by Mark@HPTuners, 03-15-2017
    16 Attachment(s)
    • Replies: 2
    • Views: 76,517
    Mark@HPTuners
    03-16-2017 Go to last post

  4. Sticky Thread Sticky: Safety Tip: Please Read Me Before you Write to any PCM/ECM with your Laptop

    Started by S2H, 02-21-2009
    3 Pages •
    1 2 3
    5 Attachment(s)
    • Replies: 42
    • Views: 141,844
    tnbubba
    07-09-2020 Go to last post

  1. VCM Security Problem

    Started by 1slowsilverado, 04-14-2006
    • Replies: 8
    • Views: 4,263
    esr
    05-06-2006 Go to last post

  2. ver 3.0 vcm enhancements. e40 ecm 2.5bar

    Started by 1TLRMS, 02-20-2016
    1 Attachment(s)
    • Replies: 4
    • Views: 2,152
    ElecTech
    02-20-2016 Go to last post

  3. Chris, Keith, THANK YOU for holiday recovery A+ A+

    Started by 2000Firehawk, 11-26-2004
    • Replies: 2
    • Views: 1,847
    ozorowsky
    11-26-2004 Go to last post

  4. You can turn the key OFF when programming ???

    Started by 2000Firehawk, 05-07-2006
    • Replies: 1
    • Views: 2,619
    Casey
    05-07-2006 Go to last post

  5. error message after READ ENTIRE, " This Is an Isuzu vehicle, hahaha, [LOL]"

    Started by 2000Firehawk, 05-08-2006
    • Replies: 5
    • Views: 2,863
    2000Firehawk
    05-09-2006 Go to last post

  6. Cannot read/write VCM after abort!

    Started by 2000gagt, 09-13-2012
    • Replies: 3
    • Views: 2,311
    Bill@HPTuners
    09-14-2012 Go to last post

  7. SD 1bar table going lean rich after reflash gen 3 issue?

    Started by 2000Phoenix, 10-13-2021
    2 Attachment(s)
    • Replies: 0
    • Views: 693
    2000Phoenix
    10-13-2021 Go to last post

  8. 2.24 2 bar os on 3.0 not working?

    Started by 2000_SS, 03-13-2016
    2 Attachment(s)
    • Replies: 3
    • Views: 1,897
    2000_SS
    03-13-2016 Go to last post

  9. Controller Unlocker: x36 Exceed Number of Attempts

    Started by 2000_SS, 05-02-2016
    3 Pages •
    1 2 3
    1 Attachment(s)
    • Replies: 51
    • Views: 42,850
    Bill@HPTuners
    05-31-2022 Go to last post

  10. Tried to write the pcm now car won't even try to crank

    Started by 2001 Pewter WS6, 12-09-2007
    • Replies: 8
    • Views: 4,865
    Bill@HPTuners
    12-19-2007 Go to last post

  11. Help!! File Wont Open

    Started by 2001blackbird, 03-09-2007
    • Replies: 11
    • Views: 5,220
    Frost
    03-22-2007 Go to last post

  12. write entire question

    Started by 2002charged, 05-09-2006
    • Replies: 1
    • Views: 1,750
    Shifted
    05-09-2006 Go to last post

  13. Reduced power mode even after adjusting P1514 graph

    Started by 2002charged, 02-02-2006
    • Replies: 4
    • Views: 2,572
    2002charged
    02-03-2006 Go to last post

  14. How to post my tune file

    Started by 2002TA, 06-04-2021
    • Replies: 1
    • Views: 876
    5FDP
    06-04-2021 Go to last post

  15. I need a new tuner

    Started by 2003SilvSS, 06-24-2007
    • Replies: 8
    • Views: 3,788
    EC_Tune
    06-25-2007 Go to last post

  16. OS doesn't support 2 bar

    Started by 2004gtols1, 05-07-2017
    • Replies: 6
    • Views: 2,989
    5FDP
    05-08-2017 Go to last post

  17. Where is OLFA table? Does it have a different name in Version 4?

    Started by [email protected], 09-01-2018
    3 Attachment(s)
    • Replies: 7
    • Views: 5,066
    mowton
    09-03-2018 Go to last post

  18. New to HpTuners

    Started by 2012CammedSS, 09-24-2018
    • Replies: 2
    • Views: 1,268
    D.Tuned
    09-25-2018 Go to last post

  19. Question for HP tech staff: minimum laptop requirement s for updated MVI2 version...

    Started by 2018 ZL1 M6, 05-19-2018
    • Replies: 5
    • Views: 6,320
    5 Star Custom Solutions
    12-13-2022 Go to last post

  20. VCM Editor v5.0.4... missing Overspeed???

    Started by 2023_ZL1-AUTO, 03-08-2023
    1 Attachment(s)
    • Replies: 4
    • Views: 793
    2023_ZL1-AUTO
    03-08-2023 Go to last post
Page 5 of 138 FirstFirst 1234567891555105 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.