Page 3 of 131 FirstFirst 12345671353103 ... LastLast
Threads 41 to 60 of 2615

Forum: VCM Scanner

General product use: Scanning, Data Analysis, Layout Configurations, ...

Sub-Forums Threads / Posts  Last Post

  1. VCM Scanner External Sensors

    Configuration and use of A/D inputs and outputs.
    Wideband/Lambda/MAP/MAF/Other sensors...

    Forum Actions:

    Forum Statistics:

    • Threads: 1,368
    • Posts: 10,823

    Last Post:

  1. Sticky Thread Sticky: Permanent DTCs and VCM Scanner

    Started by Mark@HPTuners, 11-22-2016
    2 Attachment(s)
    • Replies: 17
    • Views: 72,035
    HartRod
    11-22-2024 Go to last post

  2. Sticky Thread Sticky: VCM Scanner V3 How-To / Getting Started Threads

    Started by schpenxel, 02-12-2016
    • Replies: 2
    • Views: 114,776
    mowton
    03-27-2016 Go to last post

  3. Sticky Thread Sticky: Important instructions when asking for V3.0 Scanner assistance

    Started by mowton, 02-10-2016
    • Replies: 0
    • Views: 60,235
    mowton
    02-10-2016 Go to last post

  1. Looking for "How To" - capture a .hpt file to send in for PCM Purchase flashing

    Started by Mojo88, 01-25-2025
    • Replies: 3
    • Views: 1,000
    Mojo88
    01-25-2025 Go to last post

  2. Problems adding WB

    Started by Pavetim, 01-21-2025
    • Replies: 5
    • Views: 1,518
    Pitbull
    01-22-2025 Go to last post

  3. Is there a way to tell how many in a cell were hits?

    Started by Pavetim, 01-19-2025
    • Replies: 1
    • Views: 792
    aaronc7
    01-19-2025 Go to last post

  4. Polling rate extremely slow, even with only 3 polled channels - E38 Controller

    Started by supervette64, 01-13-2025
    2 Pages •
    1 2
    7 Attachment(s)
    • Replies: 27
    • Views: 5,092
    LilSick
    01-15-2025 Go to last post

  5. Read DTC

    Started by lynyrd, 01-15-2025
    • Replies: 0
    • Views: 398
    lynyrd
    01-15-2025 Go to last post

  6. Special functions and fuel trim reset?

    Started by Pavetim, 01-08-2025
    • Replies: 0
    • Views: 392
    Pavetim
    01-08-2025 Go to last post

  7. HOw to tell which paramater to select

    Started by Pavetim, 12-27-2024
    • Replies: 2
    • Views: 3,030
    LilSick
    12-31-2024 Go to last post

  8. 2021 Global B GM vehicle (Yukon w 6.2) - many missing variables (knock, misfire etc)

    Started by PSS, 07-20-2024
    • Replies: 4
    • Views: 14,651
    TriPinTaZ
    12-28-2024 Go to last post

  9. Help with AEM 30-0334/30-0333 Wideband to ProLink+ - Lambda Reading Stuck at 0.60

    Started by andnosobabin, 12-19-2024
    1 Attachment(s)
    • Replies: 6
    • Views: 895
    LilSick
    12-25-2024 Go to last post

  10. missing parameters in math and filters.

    Started by tonn0297, 12-20-2024
    • Replies: 2
    • Views: 1,030
    tonn0297
    12-21-2024 Go to last post

  11. new MPI3 pro link AEM 30 help

    Started by 18f1505.0roush, 12-20-2024
    1 Attachment(s)
    • Replies: 1
    • Views: 495
    18f1505.0roush
    12-20-2024 Go to last post

  12. New to HPT but not new to tuning

    Started by Cometkid, 12-07-2024
    • Replies: 3
    • Views: 2,035
    Cometkid
    12-20-2024 Go to last post

  13. No IMRC status PID for 05-10 Mustangs?

    Started by Black_Sunshine, 12-17-2024
    • Replies: 3
    • Views: 537
    Black_Sunshine
    12-17-2024 Go to last post

  14. VCM scanner Causes car to die

    Started by jase2020, 12-06-2024
    • Replies: 1
    • Views: 1,563
    Pulse_GTO
    12-09-2024 Go to last post

  15. Angry Communication Issues

    Started by n_kremer36, 12-08-2024
    4 Attachment(s)
    • Replies: 3
    • Views: 1,372
    Bill@HPTuners
    12-09-2024 Go to last post

  16. Help wiring wideband to 0411 PCM EGR

    Started by Richard2325, 06-08-2024
    2 Attachment(s)
    • Replies: 5
    • Views: 2,058
    That1talon
    12-02-2024 Go to last post

  17. BCM functions

    Started by Bill@HPTuners, 01-17-2006
    2 Pages •
    1 2
    • Replies: 34
    • Views: 25,468
    Clubby
    11-30-2024 Go to last post

  18. vcm scanner

    Started by steve smith, 11-28-2024
    2 Attachment(s)
    • Replies: 0
    • Views: 1,114
    steve smith
    11-28-2024 Go to last post

  19. Scanner being laggy

    Started by CptFalcon, 11-10-2024
    1 Attachment(s)
    • Replies: 3
    • Views: 1,983
    Alvin
    11-27-2024 Go to last post

  20. AEM 4110 will read but won't show tables

    Started by motrhedx81, 11-24-2024
    8 Attachment(s)
    • Replies: 1
    • Views: 1,311
    motrhedx81
    11-26-2024 Go to last post
Page 3 of 131 FirstFirst 12345671353103 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.