Page 7 of 126 FirstFirst ... 345678910111757107 ... LastLast
Threads 121 to 140 of 2517

Forum: VCM Scanner

General product use: Scanning, Data Analysis, Layout Configurations, ...

Sub-Forums Threads / Posts  Last Post

  1. VCM Scanner External Sensors

    Configuration and use of A/D inputs and outputs.
    Wideband/Lambda/MAP/MAF/Other sensors...

    Forum Actions:

    Forum Statistics:

    • Threads: 1,344
    • Posts: 10,644

    Last Post:

  1. Sticky Thread Sticky: Permanent DTCs and VCM Scanner

    Started by Mark@HPTuners, 11-22-2016
    • Replies: 13
    • Views: 48,928
    vet57air
    06-16-2022 Go to last post

  2. Sticky Thread Sticky: VCM Scanner V3 How-To / Getting Started Threads

    Started by schpenxel, 02-12-2016
    • Replies: 2
    • Views: 95,429
    mowton
    03-27-2016 Go to last post

  3. Sticky Thread Sticky: Important instructions when asking for V3.0 Scanner assistance

    Started by mowton, 02-10-2016
    • Replies: 0
    • Views: 33,724
    mowton
    02-10-2016 Go to last post

  1. Fuel Level?

    Started by MeentSS02, 12-23-2005
    5 Pages •
    1 2 3 ... 5
    • Replies: 89
    • Views: 43,838
    kastein
    07-11-2023 Go to last post

  2. Traction Control PID on C5 shows on with scanner

    Started by bthurman65, 07-09-2023
    • Replies: 0
    • Views: 325
    bthurman65
    07-09-2023 Go to last post

  3. 2019 L83 e92a ecu swap RPM (SAE) not reading

    Started by modularfox, 07-05-2023
    • Replies: 1
    • Views: 492
    modularfox
    07-09-2023 Go to last post

  4. HP tuners will not log 02's

    Started by CraigB, 07-02-2023
    1 Attachment(s)
    • Replies: 1
    • Views: 496
    KillboyPowerhead
    07-08-2023 Go to last post

  5. VCM Scanner Communication Issues

    Started by Lght_Spd, 06-30-2023
    • Replies: 2
    • Views: 651
    Keith@HPTuners
    07-03-2023 Go to last post

  6. How to add a clear space between channels.

    Started by K44, 02-26-2023
    • Replies: 5
    • Views: 2,029
    Millar Time
    07-02-2023 Go to last post

  7. Engine Fule rate Converting L/H into MG ?

    Started by Aus_spec_ranger, 06-28-2023
    2 Attachment(s)
    • Replies: 2
    • Views: 518
    Aus_spec_ranger
    06-29-2023 Go to last post

  8. Toyota / Lexus Knock correction learn value (KCLV) and Knock Feedback Value (KFV)

    Started by jaMIKEca, 06-07-2023
    • Replies: 1
    • Views: 784
    Romulo
    06-24-2023 Go to last post

  9. MPVI 3 connection issue (only when car is running)

    Started by onlytheclint, 06-20-2023
    • Replies: 1
    • Views: 465
    onlytheclint
    06-21-2023 Go to last post

  10. Did HP tuners brick 5.0.4?

    Started by K44, 06-19-2023
    • Replies: 6
    • Views: 878
    OhTwo
    06-21-2023 Go to last post

  11. RPM Gauge Not Reading

    Started by Wildman4x4, 06-17-2023
    • Replies: 1
    • Views: 489
    K44
    06-21-2023 Go to last post

  12. Connected to car but can?t scan...

    Started by 4.8Elcamino, 06-16-2022
    • Replies: 7
    • Views: 1,841
    K44
    06-21-2023 Go to last post

  13. Control Module Voltage VS Control Module Voltage (SAE). Difference?

    Started by TXjeepTJ, 12-19-2021
    2 Attachment(s)
    • Replies: 9
    • Views: 2,455
    slarsen47
    06-20-2023 Go to last post

  14. interface not found

    Started by _shawn_, 06-11-2023
    • Replies: 1
    • Views: 686
    Bill@HPTuners
    06-11-2023 Go to last post

  15. Adding a new car to scanner

    Started by rockofthenorth, 06-10-2023
    • Replies: 0
    • Views: 416
    rockofthenorth
    06-10-2023 Go to last post

  16. Zeitronix dual wideband zt-4 in scanner

    Started by blake-b, 06-10-2023
    • Replies: 0
    • Views: 366
    blake-b
    06-10-2023 Go to last post

  17. Question about VIN's and PCM use w/ HP Tuners

    Started by Final GTS, 05-08-2007
    • Replies: 6
    • Views: 3,169
    jeepingsteve
    06-09-2023 Go to last post

  18. Is this the Clutch Pedal Position Sensor relearn button?

    Started by Chris2008, 06-07-2023
    1 Attachment(s)
    • Replies: 0
    • Views: 446
    Chris2008
    06-07-2023 Go to last post

  19. Need some info on mph in vcm scanner not being equal to actual speed

    Started by shadowhunter, 06-06-2023
    • Replies: 0
    • Views: 352
    shadowhunter
    06-06-2023 Go to last post

  20. Question Scanner not filling cells during MAF tuning

    Started by DCZ, 05-04-2023
    1 Attachment(s)
    • Replies: 5
    • Views: 971
    DCZ
    06-04-2023 Go to last post
Page 7 of 126 FirstFirst ... 345678910111757107 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.