Page 7 of 126 FirstFirst ... 345678910111757107 ... LastLast
Threads 121 to 140 of 2515

Forum: VCM Scanner

General product use: Scanning, Data Analysis, Layout Configurations, ...

Sub-Forums Threads / Posts  Last Post

  1. VCM Scanner External Sensors

    Configuration and use of A/D inputs and outputs.
    Wideband/Lambda/MAP/MAF/Other sensors...

    Forum Actions:

    Forum Statistics:

    • Threads: 1,344
    • Posts: 10,641

    Last Post:

  1. Sticky Thread Sticky: Permanent DTCs and VCM Scanner

    Started by Mark@HPTuners, 11-22-2016
    • Replies: 13
    • Views: 47,759
    vet57air
    06-16-2022 Go to last post

  2. Sticky Thread Sticky: VCM Scanner V3 How-To / Getting Started Threads

    Started by schpenxel, 02-12-2016
    • Replies: 2
    • Views: 94,535
    mowton
    03-27-2016 Go to last post

  3. Sticky Thread Sticky: Important instructions when asking for V3.0 Scanner assistance

    Started by mowton, 02-10-2016
    • Replies: 0
    • Views: 32,973
    mowton
    02-10-2016 Go to last post

  1. 2019 L83 e92a ecu swap RPM (SAE) not reading

    Started by modularfox, 07-05-2023
    • Replies: 1
    • Views: 480
    modularfox
    07-09-2023 Go to last post

  2. HP tuners will not log 02's

    Started by CraigB, 07-02-2023
    1 Attachment(s)
    • Replies: 1
    • Views: 490
    KillboyPowerhead
    07-08-2023 Go to last post

  3. VCM Scanner Communication Issues

    Started by Lght_Spd, 06-30-2023
    • Replies: 2
    • Views: 622
    Keith@HPTuners
    07-03-2023 Go to last post

  4. How to add a clear space between channels.

    Started by K44, 02-26-2023
    • Replies: 5
    • Views: 2,002
    Millar Time
    07-02-2023 Go to last post

  5. Engine Fule rate Converting L/H into MG ?

    Started by Aus_spec_ranger, 06-28-2023
    2 Attachment(s)
    • Replies: 2
    • Views: 507
    Aus_spec_ranger
    06-29-2023 Go to last post

  6. Toyota / Lexus Knock correction learn value (KCLV) and Knock Feedback Value (KFV)

    Started by jaMIKEca, 06-07-2023
    • Replies: 1
    • Views: 772
    Romulo
    06-24-2023 Go to last post

  7. MPVI 3 connection issue (only when car is running)

    Started by onlytheclint, 06-20-2023
    • Replies: 1
    • Views: 452
    onlytheclint
    06-21-2023 Go to last post

  8. Did HP tuners brick 5.0.4?

    Started by K44, 06-19-2023
    • Replies: 6
    • Views: 855
    OhTwo
    06-21-2023 Go to last post

  9. RPM Gauge Not Reading

    Started by Wildman4x4, 06-17-2023
    • Replies: 1
    • Views: 478
    K44
    06-21-2023 Go to last post

  10. Connected to car but can?t scan...

    Started by 4.8Elcamino, 06-16-2022
    • Replies: 7
    • Views: 1,821
    K44
    06-21-2023 Go to last post

  11. Control Module Voltage VS Control Module Voltage (SAE). Difference?

    Started by TXjeepTJ, 12-19-2021
    2 Attachment(s)
    • Replies: 9
    • Views: 2,399
    slarsen47
    06-20-2023 Go to last post

  12. interface not found

    Started by _shawn_, 06-11-2023
    • Replies: 1
    • Views: 672
    Bill@HPTuners
    06-11-2023 Go to last post

  13. Adding a new car to scanner

    Started by rockofthenorth, 06-10-2023
    • Replies: 0
    • Views: 410
    rockofthenorth
    06-10-2023 Go to last post

  14. Zeitronix dual wideband zt-4 in scanner

    Started by blake-b, 06-10-2023
    • Replies: 0
    • Views: 359
    blake-b
    06-10-2023 Go to last post

  15. Question about VIN's and PCM use w/ HP Tuners

    Started by Final GTS, 05-08-2007
    • Replies: 6
    • Views: 3,148
    jeepingsteve
    06-09-2023 Go to last post

  16. Is this the Clutch Pedal Position Sensor relearn button?

    Started by Chris2008, 06-07-2023
    1 Attachment(s)
    • Replies: 0
    • Views: 431
    Chris2008
    06-07-2023 Go to last post

  17. Need some info on mph in vcm scanner not being equal to actual speed

    Started by shadowhunter, 06-06-2023
    • Replies: 0
    • Views: 347
    shadowhunter
    06-06-2023 Go to last post

  18. Question Scanner not filling cells during MAF tuning

    Started by DCZ, 05-04-2023
    1 Attachment(s)
    • Replies: 5
    • Views: 953
    DCZ
    06-04-2023 Go to last post

  19. Question Logging "external input" from main CAN-BUS ?

    Started by racemonkey, 05-31-2023
    1 Attachment(s)
    • Replies: 7
    • Views: 902
    racemonkey
    06-02-2023 Go to last post

  20. Cannot get a EQ Ratio Error Graph to run - HELP PLEASE

    Started by CTSVNZ, 05-28-2023
    • Replies: 2
    • Views: 1,561
    CTSVNZ
    05-31-2023 Go to last post
Page 7 of 126 FirstFirst ... 345678910111757107 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.