It's finally here.
2003-2004 (448K Oak ECM) and 2005-2007 (512k Oak ECM) are now supported in the latest beta. Every read that has been sent to us over the last several years has been added.
I will be working on adding TCM support over the next several weeks.
Updated thread. 2003-2005 6.0L Diesels are now supported.
Awesome! I have had countless request for tuning these over the years. I hope they come looking again soon!
Thanks again Eric!
This is awesome.. so does this mean I should hold off on getting a tuner for my 6.4l powerstroke?
I can't give you an ETA, but it only took me a month to get the 6.0L done. I would expect to be able to get the 6.4L done in a couple months.Quote:
Originally Posted by 22eco
how long until the scanner is working so we can monitor the oil temp, coolant temp, trans temp and ficm voltage with 2.24 scanner i think all we get is coolant tempQuote:
Originally Posted by Eric@HPTuners
this is great news! thank you , TCM support is equally important , I need tcm support for the 6.0 cummins conversions I do using the 5r110, this will be great.
will the 2015 6.7 be on the radar?
Just read my first diesel,got an error message afterwards "Validate Checksum Failed,you will be unable to save or flash this file".
It saved 182kb file though,and it opened up and showed some parameters.
Something odd about this duck though,Hp nor Ford IDS will recognize the VIN and I have to enter it.
It is updated to latest calibration available currently.
Any info?
This is a 2004 F350 6.0,I downloaded the latest Beta after the first read did the same thing.
Send the file into support, and I will take a look.Quote:
Originally Posted by playtoy_18
you wouldnt happen to have an 06 stock file i could look at?
http://www.hptuners.com/forum/showth...l=1#post371613Quote:
Originally Posted by Tiffo60
If you need another one, I have the one out of my personal pig. You can email me at the address in my sig.Quote:
Originally Posted by Tiffo60
Hey guys, how do I get 2.25 beta? I have a '05 psd 6.0 that I would just like to use the VCM scanner to check my coolant, oil, tranny temps etc...
Any help would be great! Thanks
email support with your infoQuote:
Originally Posted by khislop007
Just wanted to add that I have about 7 or so of the latest 6.0L TCM OSIDs now supported. I should be done tomorrow having all of them supported. So we can now say that the 6.0L ECM and TCM is supported!
Ficm ?
Possibly..Quote:
Originally Posted by richsoucie
I second that!Quote:
Originally Posted by richsoucie
Eric,
Do you still need more TCM reads? I've got 2 I can get you this weekend if you're still looking for some.
Eric,
Can I get a link to the 2.25 Beta Version Please
Quote:
Originally Posted by judeisnotobscure
You have to request access from support at hptuners dot com
Just wanted to triple check - if a customer's 6.0L F-Series truck has even so much as a transmission tune from a programmer, the file will throw a checksum error when attempting to edit, right?
I think you are using the 2.24 vcm editor.... you need the 2.25Quote:
Originally Posted by 757performance
If the tcm has been reprogrammed it should have a good checksum. If you can communicate with it over obdII you can always write in a clean stock file that will fix any checksum issue.
If you get a checksum error, send the file into support and we can take a look at it. The way the software is setup, we look for certain things when checking the checksum. If the checksum fails, but the codes for the checksum are disabled, we can assume its a non-stock file and correct the checksum automagically.
Eric,
Thanks for the clarification - I didn't want to make more work for you guys unnecessarily!
Does anyone have a config file for the 6.0? I'm trying to read EOT and ECT also I would like to see what my IPR pressure is along with all the other good stuff.
I would like this as well as ICP. FICM voltage would be great as well.Quote:
Originally Posted by khislop007
I was under the impression the scanner didn't support the 6.0's yet? If it is supported, that would be awesome!Quote:
Originally Posted by khislop007
I will be working on this pretty darn soon.
Sweet! :worship:Quote:
Originally Posted by Eric@HPTuners
Any more action on FICM tuning access yet?
We would like to change some of the injector values and voltage trouble codes.
We are looking into this, but no ETA at this time. Most of our focus is on the 6.4/6.7 at the moment.Quote:
Originally Posted by Green Tree
-Matt
How about TCM tuning for the 6.0 is there a eta available for that?
Edit just read tcm tuning is supported
Update on FICM
is this fully supported? I could only get the scanner to read the basics today. (Boost, rpm, speed, temp, map ). version 3.2. on a 2003 Ford F350 6.0 turbo. ficm? trying to figure out why this truck lacks accelleration
thanks
As of the latest beta logging is supported. I haven't tried it yet but going to either tomorrow or Saturday.
Please let me know what you find out. Are you able to run any tests to check the Glow Plugs, Injectors, Fuel Injecto Control Module, High Pressure Oil Pump HPOP, ?Quote:
Originally Posted by RandomEnthusiast
thanks!!
Haven't been able to test yet. Haven't got the beta update yet and the truck I was gonna test it on flaked out. So I'll try sometime this week.
We do not have any of the tests in there, but the parameters to log are there.Quote:
Originally Posted by Jae30001