Search:

Type: Posts; User: superman07

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    106
    Views
    13,391

    "I have not seen the normal variability in cam...

    "I have not seen the normal variability in cam phaser control amount to anything meaningful in performance. When they fail or are no where near what is commanded that changes things. "

    this is...
  2. Replies
    106
    Views
    13,391

    why do people still read the cookbook. so many...

    why do people still read the cookbook. so many better sources out there. Murfie - write a book.
  3. Thread: Whipple OS

    by superman07
    Replies
    6
    Views
    1,756

    https://www.spemotorsport.com/products/whipple-sup...

    https://www.spemotorsport.com/products/whipple-superchargers-2015-mustang-iat-harness-kit
  4. Thread: Whipple OS

    by superman07
    Replies
    6
    Views
    1,756

    there is a harness / cable everyone uses to break...

    there is a harness / cable everyone uses to break the air temp out of the MAF and to a secondary sensor in the Whipple manifold. its a 5 min deal. Dont need Whipple OS for proper temp / timing...
  5. boosted? why is MAP so high?

    boosted?

    why is MAP so high?
  6. still crickets but it looks like chevy got...

    still crickets but it looks like chevy got something new.
  7. I hope so, just bought a 2022.

    I hope so, just bought a 2022.
  8. is support from mpvi2 even likely? is it...

    is support from mpvi2 even likely? is it something they are working on?
  9. cali is fuct. vote like your fun depends on it,...

    cali is fuct. vote like your fun depends on it, it does.
  10. Replies
    6
    Views
    1,783

    "learn the changes made in the PBD tune" So if...

    "learn the changes made in the PBD tune"

    So if you dont like the PBD calibration - and I have no opinion either way, what are you expecting? So if you were able to see their changes or even just...
  11. I am running into a similar issue. Whipple used...

    I am running into a similar issue. Whipple used arbitrarily low mbt torque values for both the startup, and idle mapped points. They then used very low torque values in the torque tables with some...
  12. Thread: octane mod

    by superman07
    Replies
    26
    Views
    10,272

    Its 2021 even losers get trophies............ ...

    Its 2021 even losers get trophies............

    When is the new Ford stuff coming out?
  13. put in a support ticket. still a problem on the...

    put in a support ticket. still a problem on the whipple Cal for a gt350.
  14. Active Exhuast not working on latest beta

    Updated the software and now the gt350 exhaust doesn't work, car starts with it open, selector works but they will not close. Track mode also is not available.

    Using Whipple Cal. Going back to a...
  15. do you even have enough pump for e85.

    do you even have enough pump for e85.
  16. Replies
    63
    Views
    23,349

    Also important to understand my application is...

    Also important to understand my application is very much different than Plimmers. Its just really nice to see people with info give it back to the community.
  17. Replies
    63
    Views
    23,349

    I'm surprised you didn't lock timing to remove it...

    I'm surprised you didn't lock timing to remove it from the equation.

    Good info. -20 matches what some tuners I know have stated, the ford supercharged calibrations I have seen dont quite retard...
  18. Replies
    13
    Views
    4,217

    fuel pressure gauge on regulator? what...

    fuel pressure gauge on regulator?

    what pressure do you have it set to?
  19. Replies
    13
    Views
    4,217

    When it doesn’t make sense. CHeck what you “know...

    When it doesn’t make sense. CHeck what you “know to be true” forget the old car, it’s gone. This is a new car.

    I would take a idle vacuum measurement, and verify fuel pressure at the rail at...
  20. Are you hitting a combustion stability limit...

    Are you hitting a combustion stability limit somewhere? It looked like the only fueling table with a lambda value that low.
  21. Replies
    14
    Views
    3,078

    There may be something more too it. I cant and...

    There may be something more too it. I cant and dont feel like going back to find older logs in which I had issues with the cams following the "expected angle". But I have seen it no less than 3...
  22. Replies
    22
    Views
    5,991

    I saw nothing different in your file of any...

    I saw nothing different in your file of any importance.

    have you checked all the wires / connectors to your VCT solenoids. Literally just saw two guys post on a fb forum last night a similar...
  23. Replies
    4
    Views
    2,079

    On my car I needed to go into the mapped point...

    On my car I needed to go into the mapped point that was used for idle and bump the torque up just a bit. didnt take much at all. This made the torque request command just a bit less load, which...
  24. Replies
    22
    Views
    5,991

    I’ll check it with my 2016 stock file tonight.

    I’ll check it with my 2016 stock file tonight.
  25. Replies
    22
    Views
    5,991

    Murfie has given you incredibly sound info, where...

    Murfie has given you incredibly sound info, where is your calibration? can you not post it?
Results 1 to 25 of 191
Page 1 of 8 1 2 3 4