Anyone have a link where I can download 2.4? I am not ready to make the change to 3.0 just yet and when I installed it I lost my old version.
Type: Posts; User: slammin86
Anyone have a link where I can download 2.4? I am not ready to make the change to 3.0 just yet and when I installed it I lost my old version.
I'm at a loss here. Anyone know if this is possible?
I tried with 2.24, 2.25 and now 3.0. Can't find it anywhere.
Well for the time being I just lowered my IAC counts down from 60ish to 40ish. This gives me more air all over. It is just a bandaid for the time being and I would still like to hear some other...
A little back story here. I recently swapped heads on my 04 gto and have been in the process of redoing the idle. Mods are as follows.
229/234 .612/.600 111+4 cam
Trick flow 220's hand ported...
Until this year my car has always hibernated in the garage during the winter months but this year I have had to drive it some. I am having a cold start issue that I have tried working through on my...
My friend has a 06 GTO and his does the same thing. Never seen it on another car though.
Here is the background.
A friend of mine recently did a cam and head swap on his car. He also swapped in a 2 bar map sensor because he is going to put a turbo on soon. He came out to my house and...
I am unable to read your tune...must be 2.23. Can you post a screenshot of how your tables are set up? Or just give me the numbers?
Thanks you I appreciate that. I guess I can try this one...
I am tuning a camaro later today. The guy is doing a turbo build but the turbo is not on yet. He has done the heads, cam, and 2 bar map sensor from a cobalt ss (pn 12615136). I am working on a...
I have a 04 GTO with a small/ medium size cam, stock 243 heads & kooks longtubes.
I have 42 lb green tops with the Greg Banish injector data.
About a month ago I decided to go with catless...
Yes you have the right table. Unplug your iat and log to see what temp it is actually at. Then take that whole column and the ones next to it and subtract out whatever you wanna pull.
OR...
...
It is disabled while dialing in the ve and maf tables.
I just got my upgrade today. Is there any special precaution I need to take to ensure that I do not loose any of my hp tuners stuff, or can I just install it? I figure I will save a copy of all my...
Woah nice post. I too would like to hear more about this.
My friend has a 02 camaro that we were tuning tonight. The car has pacesetter long tubes, lid, ported tb, and no cats. He used the 13111 corvette rear 02 sensor as his primary 02 sensors, and his...
I have a aem that I run all the time, then I also have a lc1 that can be moved from car to car.
I cant wait to see what else is in store for the upgrade.
I loomed mine up pretty well to make it portable. I connected all the grounds to a single 14 ga wire. I connected the power to a single 14 ga wire. I then put a fuse on the end of the power, and...
I guess I need to just get the software installed and mess with it for awhile.
On my aem gauge when I unhook the sensor from it, it reads a steady state 14.8 I believe. I can then adjust my offset inside hp tuners until it matches.
My innovate lc1 has come in. I have not...
Pretty happy with mine.
I do not think the table we are talking about has anything to do with torque management. It is on the same tab as the high and low octane tables.
I too have wondered exactly what the max torque timing table does.
Do you mean zeroing out the throttle cracker table?
So I ran the idle russ k idle config today. I kept the fans shut off, and let it idle up to about 225.
Afterwards I went for a drive. It took a little bit for the car to stay running on its own....