Search:

Type: Posts; User: bugsy

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    16
    Views
    11,510

    EGT Leave the offset but adjust the slope. set...

    EGT
    Leave the offset but adjust the slope.
    set up the scanner to read the map and also the barometric pressure.
    Remembering that bosch sensors have a slight variance from sensor to sensor.
  2. Thread: Na to turbo

    by bugsy
    Replies
    12
    Views
    7,249

    Rolls is correct. The pistons are a cast alloy...

    Rolls is correct.
    The pistons are a cast alloy not forged.
    The rods are the same as the ba small rod.
    High comp with very little room for error.
    I am playing with a fg na motor for now and boost...
  3. Replies
    162
    Views
    64,198

    The map sensor is reading correctly until it hits...

    The map sensor is reading correctly until it hits the max on the pid which is 255kpa which was confirmed by Eric that it was due to the pid.
    Eric is doing the DMR for my osid so we can test further....
  4. Replies
    162
    Views
    64,198

    The latest I have heard about SCT is that they...

    The latest I have heard about SCT is that they were happy to say that they had a car driving around with a 3 bar map sensor only.
    They had not done the boost sensor or gone for the higher map...
  5. Replies
    162
    Views
    64,198

    Hey guys... we have a winner Tested the...

    Hey guys...

    we have a winner

    Tested the idle park and idle in gear.
    Idle in park will read below the map sensor range but if you have the a/c on it brings it back into range.

    Can't thank...
  6. Replies
    162
    Views
    64,198

    Ok guys it is finally getting there. A few more...

    Ok guys it is finally getting there.
    A few more adjustments and it should be good.
    I have just put the 4 bar map and boost sensors back into my car and the tables worked.
    Just need a minor fix...
  7. Replies
    162
    Views
    64,198

    Eric. I have emailed you some results.

    Eric.
    I have emailed you some results.
  8. Replies
    162
    Views
    64,198

    I am only testing for the b series and territory

    I am only testing for the b series and territory
  9. Replies
    162
    Views
    64,198

    Thanks Eric

    Thanks Eric
  10. Replies
    162
    Views
    64,198

    Did you finally get your map sensor going Steve?...

    Did you finally get your map sensor going Steve?
    We spoke about this a few weeks ago on the phone.
  11. Replies
    162
    Views
    64,198

    Eric, Can you put it to the HACH4K6 os for me to...

    Eric,
    Can you put it to the HACH4K6 os for me to test?
  12. Replies
    15
    Views
    6,472

    Thanks fletch I will give it a try tomorrow ...

    Thanks fletch
    I will give it a try tomorrow
    Thanks again
  13. Replies
    162
    Views
    64,198

    Toads I did have both the 3.5 and 4 bar....

    Toads
    I did have both the 3.5 and 4 bar.
    Decided to go the 4 bar as it has a better range.
    I am actually going back to the 3 bar after i fit my larger turbo as i will not be exceeding 30psi.
    The...
  14. Replies
    162
    Views
    64,198

    As requested Darryl has explained it. Thank you

    As requested Darryl has explained it.
    Thank you
  15. Replies
    162
    Views
    64,198

    I will get a data log for you guys when i put it...

    I will get a data log for you guys when i put it on the dyno.
    My AEM failsafe recorded a boost reading of 30.8psi.
    The timing was set at 4? so maybe that pushed the boost up a little.

    Within the...
  16. Replies
    15
    Views
    6,472

    That would be very helpful fletch. Thank you

    That would be very helpful fletch.
    Thank you
  17. Replies
    162
    Views
    64,198

    I will be doing some more testing in the next...

    I will be doing some more testing in the next couple of weeks.
    So far I have been able to run closed loop boost up to 30psi.
    On the test run it had no timing into it as it was just a test.
    It did...
  18. Replies
    15
    Views
    6,472

    Sweet. Thanks Jet.

    Sweet.
    Thanks Jet.
  19. Replies
    15
    Views
    6,472

    Its a complete standard car. He wanted to get it...

    Its a complete standard car.
    He wanted to get it tuned but can't read the file.
    When we tried to do a read it came up with a vin of ??????????????.
    Then went straight to vheck sum fail.
    Haven't...
  20. Replies
    15
    Views
    6,472

    Never been tuned. Just wondering if it is...

    Never been tuned.
    Just wondering if it is because the instrument cluster holds all the vin and calibration info?
  21. Replies
    15
    Views
    6,472

    Got a check sum validation failed error now. But...

    Got a check sum validation failed error now.
    But still now joy.
    Have to wait for Eric to look at the file.
  22. Replies
    15
    Views
    6,472

    Ok Have tried an older build of beta and the...

    Ok
    Have tried an older build of beta and the standard 2.24 as well.
    Have now trying another thing now.
    Will let you know how we go now
  23. Replies
    15
    Views
    6,472

    Late 2014 FG xr6 not reading

    Hi Guys.
    Having issues reading a tune on a late 2014 xr6 turbo.
    Has anyone else had this issue?
  24. Replies
    162
    Views
    64,198

    Yeah mate I agree. Wish we had access to the...

    Yeah mate I agree.

    Wish we had access to the map sensor programming so that it could be done and finalized.
  25. Replies
    162
    Views
    64,198

    Due to the lack of response , we have had to go...

    Due to the lack of response , we have had to go along the line of fudging.

    We would have preferred the rescaled t-map but who knows how long that could take before becoming available.
Results 1 to 25 of 133
Page 1 of 6 1 2 3 4