Search:

Type: Posts; User: Chad D.

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    186

    Nice. Nice.

    Nice. Nice.
  2. Replies
    3
    Views
    186

    @Slow&Stock was a huge help with my cruise setup....

    @Slow&Stock was a huge help with my cruise setup. Maybe he will have a good suggestion on where to look. Pretty sure you?ve thought of everything I would have thought about, but I can forward my...
  3. Replies
    2
    Views
    282

    Forgive me if I?m not remembering how it worked...

    Forgive me if I?m not remembering how it worked when I had my 2018 Tundra tuned, but don?t they send you a stock tune file for your truck when you purchase credits to register your VIN? HP?s website...
  4. Too many variables for most folks to just give a...

    Too many variables for most folks to just give a file up that could leave them feeling a little skeptical, I?d bet.

    I?d suggest looking to some reputable Tundra tuners for help with a remote...
  5. Replies
    2
    Views
    1,091

    It?s intimidating, for sure! I was in your...

    It?s intimidating, for sure! I was in your shoes a year ago, but have gained confidence and don?t mind fiddling around with my tune a bit.

    I did start with a tuner shop that got everything...
  6. Replies
    5
    Views
    1,366

    Yep! What he said ^^^. The Toyota ECM is a...

    Yep! What he said ^^^. The Toyota ECM is a write only. There is no reading what you have.
    Every time I update my tune, I open the latest file and ?save as?. Each revision is numbered. ...
  7. Replies
    6
    Views
    1,165

    Gotcha; I think... Is the goal to lower the rev...

    Gotcha; I think... Is the goal to lower the rev limiter for some reason? Guessing it must be just for sound and no performance gains. Having a tough time wrapping my head around this.
  8. Replies
    6
    Views
    1,165

    Forgive my ignorance, but what is ?cutoff?? Not...

    Forgive my ignorance, but what is ?cutoff?? Not familiar with the term in this world.

    Whatcha wanting it to do?
  9. Did really well. Thanks for asking! I did...

    Did really well. Thanks for asking!

    I did have to make a couple minor adjustments, most notably decreasing tps for upshift. I needed a little higher hysteresis.

    Since these adjustments,...
  10. Following up after some assistance from our...

    Following up after some assistance from our resident Tundra HP Tuners guru, SlowNStock.

    My 6th gear TCC releasing issue is no longer! With his help, my TCC remains locked in 6th gear right till...
  11. Ok! Thanks once again to SlowNStock for the...

    Ok! Thanks once again to SlowNStock for the huge help! Got the new revision loaded in and so far it feels great. I won?t hit my nemesis hill till Sunday morning, so will report back again after...
  12. Thank you for that explanation. I'll see if he...

    Thank you for that explanation. I'll see if he can do some logging soon and confirm that is (or is not) receiving input shaft RPM. Scanning and logging is new to both of us, so hopefully we can...
  13. Not 100% sure how to find that?. The only thing...

    Not 100% sure how to find that?. The only thing I?ve done related to that was determine the revs per mile based on tire circumference and axle gear ratio. Tires go round about 517 times per mile...
  14. Ah, copy. I did misinterpret some things earlier...

    Ah, copy. I did misinterpret some things earlier on?

    I?ll go back and revise!



    Edit: I just tried to figure this out, but there is not a table for 6th gear TCC work in the AI/CRUISE/COAST...
  15. Thanks again; this is making sense. Not...

    Thanks again; this is making sense.

    Not knowing where he?s currently shifting, I multiplied all shift point initiation rpm by 75% to see if that gets us going through the gears.

    I also...
  16. Ok. Thanks for this detailed post! Very...

    Ok. Thanks for this detailed post! Very appreciated.

    If I?m wrapping my head around it correctly, he may still be in a bit of a pickle since he has two drive ranges within the transfer case. ...
  17. @SlowNStock, I may have misinterpreted some of...

    @SlowNStock, I may have misinterpreted some of your info.

    I made all of my TCC release changes in the NORMAL tables. Do I need to copy those changes into the AI/CRUISE tables also?
  18. Still struggling with my friend?s transmission...

    Still struggling with my friend?s transmission tune. But, I just learned that his speedo sensor is being read from the trans output, rather than t-case output because his Atlas transfer case doesn?t...
  19. I think I'm getting closer, no doubt because of...

    I think I'm getting closer, no doubt because of the awesome help and insight provided on this forum.

    I've added a little at a time to the TRANS>TORQUE CONVERTER>LOCK APPLY/RELEASE>OUTPUT SPEED...
  20. Hoping to hear something on this as well! I'll...

    Hoping to hear something on this as well! I'll be trying to help a friend with a similar issue this evening. He has to lift to get it to shift when the tires are spinning. This is in a rock...
  21. Replies
    11
    Views
    3,313

    I did! Truck runs amazing?. I?m doing some...

    I did! Truck runs amazing?. I?m doing some very small adjustments to see if I can get the torque converter dialed in a little better, but that?s not FTW?s fault. I only had Chris work on the...
  22. Agreed. The info that @SlowNStock is sharing...

    Agreed. The info that @SlowNStock is sharing here is awesome! I've already rewritten my TCC unlock pattern and will flash it as soon as I can. His explanation of how these updates should affect...
  23. OK. Quick question for clarity, @SlowNStock. ...

    OK. Quick question for clarity, @SlowNStock.

    I've done this (copy/paste from your explanation):
    For example, if we are cruising in 6th at ~2000 RPM without Tow/Haul on, we would find the axis...
  24. Got stuck on a house fire for a few hours after...

    Got stuck on a house fire for a few hours after work today, and just got home. I?ll bring my MPVI3 to work tomorrow and dick around with the TCC tune on the clock. I?m spent for the night.
  25. Holy smokes! That?s a heluva response; much...

    Holy smokes! That?s a heluva response; much appreciated!!!

    I?ll pick through all of that when I haven?t had a couple cocktails with dinner?
Results 1 to 25 of 37
Page 1 of 2 1 2