hi
supercharged ,cammed and manual swapped crown vic
the car had only one issue
the car always stall when engaging clutch and needs to press pedal for couple seconds after start up to idle
i...
Type: Posts; User: 3.6P
hi
supercharged ,cammed and manual swapped crown vic
the car had only one issue
the car always stall when engaging clutch and needs to press pedal for couple seconds after start up to idle
i...
return it back to stock values
dont mess with throttle angle
if you open key on and press pedal with out starting the car you can see throttle fully open at 75-76% TPS
if you want to increase...
thanks
i have tried disable rpm error didn't work
still command 5XX rpm at drive
there is no knock , yeah timing lower than the tune because the log before i increased timing
on 1 to 2 shift...
post your tune and log for the car
explain more idle hang or stall ?
hi
crown victroia stock engine with bolt ons and stage 5 comp cams (XE278AH)
tuning the car was fine for WOT and CRUSING but idle bring me headache
at neutral or park fine with increasing rpm...
hi guys,
4.6 2v with big profile cam
the car at idle barley have vacuum
PCM throws p0106 * map performance*
i know rising Calc Map max will solve this problem
but what's the equation for...
thank you decipha
Engine > Torque Model > there are 2 tables Engine torque and Inverse
if i increase value at idle cell from Inverse Table will make idle spark jump
if can you make...
I've tried before with idle tables without no success
if lean it out to 19:1 at idle start to chop and timing jumps from 15-25 around that but i dont like exhaust smell
if you have any suggestion i...
hi guys,
4.6 2v bolt ons and cammed crown vic
mid cam : XE268H
Intake Duration at .050 Inch Lift:230
Exhaust Duration at .050 Inch Lift:236
Intake Valve Lift:0.5
Exhaust Valve Lift:0.5
Lobe...
we need your stock tune
did you have cats ?
pops will destroy your cat's
hi
2010 charger
i'm getting this error Controller Locker : Undefined X7F Negative Response Code
while writing 30 seconds later of writing has stopped and error shows up (TIME OUT) after that i...
nope, if you wants the most hp of your engine shift around 6000 rpm if the car have few mod
bolt ons shift around 6100
4.6 screams loud at high rpms its normal that engine have a nice tone
if...
110845
rev limit and trans tune
what is your mods and fuel
Thanks decipha for the information
so, i changed ATT table only
normal and high load still 45 psi
is that ok .?:rolleyes:
110830
2008 crown vic 4.6 2v
hi guys,
Fixed fuel pressure set to 45 psi
for desired fuel pump pressure tabless :
-Ambient air temperature AAT
110819
-High load
110820
-Normal
110821
post a thread
At Wot u will see Tps around 76% its fully open u can check it
remove intake turn ignition on
press pedal fully and check it
update : 2017 post :rolleyes:
thanks
any suggestions by tuning
hi guys
i have bad experience with new oem BOSCH o2 sensors they always take about 2 minute to warms up and makes fuel trims stuck full lean with longtubes headers
i never had any problems with old...
it happen sometime often with me
close vcm suite and unplug mpvi2
plug it again and resync it should work if you car already licensed
any future support for this platform? 1998-2004 vic's
u can change gear ratio very easy dont worry but needs a tune
u can use hptuners by vcm suite
some cars dont need credits and you can change gear or tire ratio by vcm scanner like dodge
but crown vic's need a tune by vcm suite which need credits
stock...
i did experiment guys
i unplugged IAT sensor Immediately check engine light came on
tried the same things on CAM phaser's nothing happen no Check engine light so, its bad PCM or what
i started...