I just wanted to update that this will also work on a 2007. You'll have to just write entire the trans. I assumed it wouldnt, so I tried the Suburban file (had issues) then flashed this one in, and...
Type: Posts; User: simman22
I just wanted to update that this will also work on a 2007. You'll have to just write entire the trans. I assumed it wouldnt, so I tried the Suburban file (had issues) then flashed this one in, and...
The 1-2 will be on in park, reverse, neutral, and drive (1st) and so on. What happens when you drive it? Have you ran it on jackstands to circulate fluid through the trans and valve body so valves...
Have you verified at the trans plug that the pcm is sending the ground signal to energize the shift solenoid? What are your symptoms?
I was going to say that it seems like you did the swap harness and the 80e segment together and it’s interfering. They have the best reputation for making these work easily and reliably, so I’m sure...
So I did some digging in my folder of making that tune and remembered that I did pull a file from a thread that had that diagnostic ID in it. I did this entire swap in one day and tried multiple...
So I segment swapped the three HPTuners gives the option of and did a write entire. That’s when I had the issues as well as the U code saying that it lost communication with TCM/PCM. From there I...
I just picked up a 2006 TBSS, which has always been a dream to own, that had a few thrown rods. I swapped my 408/4l80E into it and came across the issue where the VSS wouldn't populate in the...
I looked it over for you and on the tcc 0% unlock, I believe what you have fixed your issue (since it?s been a week) but I normally zero all 4 of those. Have you wideband tuned it? Looks like you are...
Finally got the stall and got it all together, turned out that the 3-2 valve was broken at the connector.
Just like he said, log while you are making changes and try to hit as many ?daily driving? scenarios as you can to make sure you didn?t change something you liked before. The first big cam I had, I...
Bump. Has to be a 0411 or newer pcm
He is saying he wants to raise the speed in order to make it shift at a higher rpm.
Stock stall still? And add 2 or three to like 44% and below and then blend the next three columns to make it smooth and see how you like that. That?s about the only general change I would make, after...
What size cam and engine do you have? It?s pretty easy overall, I would log different steady TPS pulls and find out where the lugging happens and then add 2mph at a time until you like it. If you add...
I was wondering if someone could log the 1-2 and 2-3 shift solenoid status (on-off) with the key on and engine off to see if the 2-3 is on. Just completed an M6 to A4 swap and when I turn the key on,...
Recently I have been having issues with the standalone data logging (this is the first time I?ve used it since the new VCM Suite came out). I set it up like I always have in the past (pretty much...
Glad it helped. It was driving me crazy and of course all I could think was some mechanical issue somewhere haha
Oleblu and really anyone that stumbles across this, I got it figured out on mine. The box under Speedo>Calibration>Gear Ratio and Tire Size was off. I'm not sure why it didn't update correctly like...
Good to see I’m not the only one. I tried to do a new segment swap and rescale with the gear/tire wizard hoping it was just a weird glitch but nothing. If you didn’t look at the tune and just drove...
If it’s an electronic speedo then the 80e input speed sensor and output speed sensor are plugged in backwards. Been there haha
I just had a quick question about the tuning for a 4000 stall because I have never had one this loose. The setup is a 228r cam and bolt-on 6.0 with a 4l80e, FTI 4000 Hard Hit stall, and 3.42 gears...