Search:

Type: Posts; User: Baldturbofreak.com

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Well I just confirmed my hypothesis. If you run...

    Well I just confirmed my hypothesis. If you run blue top solenoids along with a built, high line pressure trans you need to modify the Commanded PCS Current table in the lower pressure regions by...
  2. Im having the same problem with a friends SRT8...

    Im having the same problem with a friends SRT8 Jeep with a SHR full billy badass trans with the blue tops. From what I have read they have a different orifice, winding and return spring. Since WOT...
  3. Replies
    22
    Views
    3,210

    My 2016 has about 30K on it now and I have begun...

    My 2016 has about 30K on it now and I have begun to notice a rougher idle/cruise then when it was new. Especially after the GM recall reflash concerning the DPF sensor. I'm going to log balance...
  4. Replies
    7
    Views
    925

    converting the op system to one of the enhanced...

    converting the op system to one of the enhanced versions from HPT will require a "write entire"
  5. Replies
    7
    Views
    925

    These were just calibration only reflashes that...

    These were just calibration only reflashes that take less then 10 seconds. This is what has me puzzled.
    Agreed, a write entire is best done with a benchrig or clean DC aux supply.
    In the case of...
  6. Replies
    7
    Views
    925

    I just experienced the same thing last night on a...

    I just experienced the same thing last night on a 2017 spark 1.8L NA with a turbo kit on it. I'm working thru the tune on the dyno and around the 10th flash it gave me that message on the DIC.
    HPT...
  7. I noticed that on mine to, I just assumed the...

    I noticed that on mine to, I just assumed the difference was just x4 cyl
    Has anyone else noticed that the MAF reads bonkers, between min and max nonstop.
  8. 2017 spark NA motor, anyone know what ecu to read it out as?

    3.6.26 has a bunch of dropdowns for the ecu type. Not sure if that's the new way things are done or it's simply not supported yet. Anyone get one to read out yet?
  9. Replies
    188
    Views
    246,010

    Sticky: Hmm I may have spoken too soon. I got it to work...

    Hmm I may have spoken too soon. I got it to work that afternoon, but get bluescreen everytime I plug the module in now. Anyone have any tips?

    Win7/64 Asus G73S
  10. Replies
    188
    Views
    246,010

    Sticky: Update, delete every driver you can find relating...

    Update, delete every driver you can find relating to the interface. For some reason win7 64 will ignore an overwrite. You must remove them completly. Then download the signed drivers again, unzip and...
  11. Replies
    188
    Views
    246,010

    Sticky: I have gotten the software to work fine with no...

    I have gotten the software to work fine with no framework issues on my new laptop.

    However it will not recognize the interface. I downloaded the signed drivers inthe link. unintstalled the...
  12. Replies
    239
    Views
    63,123

    Yes please!

    Yes please!
  13. Replies
    239
    Views
    63,123

    Thanks, Car needed ALOT of work after being...

    Thanks, Car needed ALOT of work after being driven over boulders at 80mph. Still isnt 100% and is a few $G's away from being drivable.
  14. Replies
    239
    Views
    63,123

    Any Ideas when we will be up to bat again Bill?...

    Any Ideas when we will be up to bat again Bill?
    I almost have my GXP back together with a VERY big turbo aboard.
  15. Replies
    4
    Views
    3,609

    Id try lookign over at openecu.org

    Id try lookign over at openecu.org
  16. Just make sure they are in the primary tables or...

    Just make sure they are in the primary tables or they wont show up in the dash.
  17. It does so by correlating the knock sensor with...

    It does so by correlating the knock sensor with crank/cam position withing ht engine cycle
  18. open up the table (primary), right next to the...

    open up the table (primary), right next to the save button on the toolbar.
    erase 4 slots that we arnt using. Then right click, hit "insert" and add the 4 knock cyl to the primary table.
    Then they...
  19. If it isnt being recorded in the "table display"...

    If it isnt being recorded in the "table display" screen the rest of them, histogram, chart etc will be dead Ken.
    Give that a swappin and retry.
  20. I heard over at landover baptist church that...

    I heard over at landover baptist church that windows vista is the devil!
  21. Sweet, much appreciated!

    Sweet, much appreciated!
  22. Can LNF knock sensors be seen independantly

    A customer of mine is having some serious false knock issues, since I cant connect to a LNF at the moment (mine is apart) can someone look while connected to their LNF to see if knock sensors 1/2...
  23. Replies
    239
    Views
    63,123

    Weird, my 07 msut be programmed different then...

    Weird, my 07 msut be programmed different then that particular car. I have logged high rpm using my dashturkey and have never seen DI pressure fall off from 2146psi.
  24. fuel pressure vs load ftw!

    fuel pressure vs load ftw!
  25. Is it pegging the MAF? what is the...

    Is it pegging the MAF?


    what is the description of P0014?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4