Search:

Type: Posts; User: Gustavo

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    15
    Views
    2,436

    I see, they've flashed your ECU with a stock...

    I see, they've flashed your ECU with a stock tune! Sultan's been known in the country of how good he's. All the best.
  2. Replies
    15
    Views
    2,436

    You have a code that is causing this retarding...

    You have a code that is causing this retarding "Safety measure". The E92A ECM logic works differently when engine related codes are detected. It retards the timing!
  3. Replies
    2
    Views
    977

    Just select none to camshaft under Airflow >...

    Just select none to camshaft under Airflow > Variable camshaft.
  4. Yes, if you retained the original pump assembly.

    Yes, if you retained the original pump assembly.
  5. Fuel Sys > General > FPCM Fitted = No You...

    Fuel Sys > General > FPCM Fitted = No

    You should be good to go.
  6. 120054

    120054
  7. 120053

    120053
  8. Replies
    11
    Views
    3,732

    Your EQ ratios are fluctuating spikes, try...

    Your EQ ratios are fluctuating spikes, try adjusting to have it in a linear manner. Moreover, the flex fuel sensor is turned off in the tune, how did you run the ethanol ? Did you enable it before...
  9. Replies
    1
    Views
    491

    Could be fueling, could be too sensitive sensors,...

    Could be fueling, could be too sensitive sensors, multiple variables in fact. However; to narrow down, a log is recommended in this case.
  10. Replies
    19
    Views
    5,148

    118329 Please share a data log.

    118329

    Please share a data log.
  11. Replies
    10
    Views
    2,161

    No problem at all, and no it's not going to harm...

    No problem at all, and no it's not going to harm anything, I just wanted to ask. Let me know the results with the drivability.

    All the best
  12. Replies
    2
    Views
    1,517

    You need to change few tables related to max and...

    You need to change few tables related to max and min sparks as well as logging the mapped points where the idle falls under, don't forget the idle tab and have your minimum values match the desired...
  13. Replies
    10
    Views
    2,161

    This should fix your drivability issues. 118244

    This should fix your drivability issues.

    118244
  14. Replies
    10
    Views
    2,161

    Any specific reasons why you're on SD rather than...

    Any specific reasons why you're on SD rather than MAF ?
  15. Replies
    10
    Views
    2,161

    When cold starting up the car, do you get...

    When cold starting up the car, do you get backfire through the intake ?
  16. Replies
    11
    Views
    3,732

    Here you go dear 118007

    Here you go dear

    118007
  17. Replies
    5
    Views
    1,009

    Here you go dear 118005

    Here you go dear

    118005
  18. There's one fix that had been applied to a...

    There's one fix that had been applied to a friend's car, where the nut (that's preventing the full closing) which holds the TB blade had to be unscrewed allowing the blade to be free. That for (him)...
  19. I have swapped this 102 into my Caprice and it...

    I have swapped this 102 into my Caprice and it did work perfectly. However; when resetting the TB via scanner, power reduced kicks back in.
  20. I suggest to keep the TB and write this file....

    I suggest to keep the TB and write this file. Good luck


    117649
  21. Replies
    2
    Views
    821

    You should never set the Dynamic Airflow High to...

    You should never set the Dynamic Airflow High to 200, always keep it in around 4k rpm. Even if you're on MAF tune.
  22. Replies
    8
    Views
    1,749

    Check your electrical connectors, try forcing the...

    Check your electrical connectors, try forcing the fans to turn off using VCM scanner, if they don't respond it's electrical related. File seems fine
  23. 117594

    117594
  24. Replies
    23
    Views
    5,138

    Yes sir, doubling Stoich will alter so many other...

    Yes sir, doubling Stoich will alter so many other fueling and airflow tables which will make it a hassle for you.

    Keep an eye on the cylinder airmass values tho, they may get changed.
  25. Replies
    23
    Views
    5,138

    I suggest to return the Stoich values back to...

    I suggest to return the Stoich values back to stock and re-adjust your MAF and timing. Use the below tables:

    117148

    117149

    All the best,
Results 1 to 25 of 44
Page 1 of 2 1 2