Search:

Type: Posts; User: c0ke

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    12
    Views
    3,429

    Thanks I'll look into that. The maf was off...

    Thanks I'll look into that. The maf was off because the intake pipe collapsed a little bit and was sucking in some unmetered air. plastic pipe unfortunately
  2. Replies
    12
    Views
    3,429

    Thanks also didnt work

    Thanks also didnt work
  3. Replies
    12
    Views
    3,429

    Yes I have done that already, I tried lower loads...

    Yes I have done that already, I tried lower loads like you suggested and that didn't solve it either
  4. Replies
    12
    Views
    3,429

    Thanks I also noticed the map combustion limit...

    Thanks I also noticed the map combustion limit was kinda low so I raise that also but neither of these have solved the problem yet
  5. Replies
    12
    Views
    3,429

    TQ RED. < Driver Demand

    Running into some throttle limiting, here's the file and a log if anyone could take a look on a GT350 supercharged



    112436

    112437
  6. Replies
    3
    Views
    2,858

    Thanks it was to the left of the obd port driver...

    Thanks it was to the left of the obd port driver side
  7. Replies
    3
    Views
    2,858

    2018 Ram Smart Access cable location

    Does anyone know where to install this cable?

    2018 ram longhorn 1500
  8. Replies
    5
    Views
    1,153

    Out of curiousity why not include them when...

    Out of curiousity why not include them when unlocking an 18+ pcm or purchase of a smart access cable?
  9. Replies
    5
    Views
    1,153

    it's behind the navi/radio screen. HPTuners...

    it's behind the navi/radio screen.

    HPTuners should really make a guide for each vehicle they support on this :)
  10. Replies
    5
    Views
    1,391

    yes it idles now however still can't get it to...

    yes it idles now however still can't get it to rev up or drive it goes instant lean no matter what i do to the ve chart
  11. Replies
    5
    Views
    1,391

    Yes all injector info is input correctly except...

    Yes all injector info is input correctly except the ifr

    Not sure how I did that, try this file

    map sensor is a gm 12592525, it was wired wrong

    104023
  12. Replies
    5
    Views
    1,391

    05 6.0L injector/starting issues

    Here's tune and log.

    I can only get it to start with if I set IFR any where from 10-20lbs

    Mods are:

    Holly intake
    85lbs fast injectors
    twin turbo
    forged 6.0L
  13. Replies
    15
    Views
    4,096

    102316 stock 2020 F150 Limited

    102316

    stock 2020 F150 Limited
  14. Replies
    5
    Views
    2,132

    definitely possible, add as much more to the log...

    definitely possible, add as much more to the log as possible, helps a lot with diagnostic
  15. Replies
    2
    Views
    3,860

    auto or manual? post tune

    auto or manual? post tune
  16. Replies
    1
    Views
    2,813

    https://www.hptuners.com/vehicles/ Not on...

    https://www.hptuners.com/vehicles/


    Not on the list
  17. Replies
    5
    Views
    2,132

    Have you tried pulling timing and seeing if it...

    Have you tried pulling timing and seeing if it gets rid of it? some areas have an extra 10 degrees over stock otherwise thinking maybe it has to do with your injector settings
  18. try unplugging mpvi from obd and unplugging cable...

    try unplugging mpvi from obd and unplugging cable from mpvi and cable from laptop then connect them all again 1 by 1.

    make sure you have a charger on the vehicle

    also open a support ticket for...
  19. Replies
    5
    Views
    2,132

    post tune, I don't think 50 degrees of timing is...

    post tune, I don't think 50 degrees of timing is helping your issue.....
  20. This. Which is under the torque management...

    This. Which is under the torque management section.

    But what do I know :)
  21. Replies
    4
    Views
    1,842

    Yeah looks very familiar to those 07 C6 Z06...

    Yeah looks very familiar to those

    07 C6 Z06
    E38, GM Gen4 V8
    OS: 12614676 -> 1250213
    Speed Density - 2 bar
  22. Lots of areas in the torque management section...

    Lots of areas in the torque management section need work....

    Watch logs and play in that area till you fix it :)
  23. Replies
    4
    Views
    1,842

    Yes

    Yes
  24. Replies
    22
    Views
    14,168

    1 lambda unless otherwise adjusted.... I'm...

    1 lambda unless otherwise adjusted.... I'm telling you there isn't much if anything that hptuners hasn't covered for the m156
  25. Need to log a lot more to know what and where to...

    Need to log a lot more to know what and where to adjust.... Needs some fuel and maybe a tad less timing or the knock sensors dialed in for headers, I would recommend doing some more research and at...
Results 1 to 25 of 52
Page 1 of 3 1 2 3