Search:

Type: Posts; User: JaegerWrenching

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Regeneration isn't only based on pre and post DPF...

    Regeneration isn't only based on pre and post DPF pressure. It will command a regeneration After X amount of miles or X amount of run time, even if it doesn't show any pressure difference. In order...
  2. Post your tune file

    Post your tune file
  3. What are you using to get a RPM signal to the...

    What are you using to get a RPM signal to the PCM? What does battery voltage look like? I'd check for good grounds and make sure the trans has a ground coming off it to the frame. i believe those...
  4. Replies
    24
    Views
    345

    40 PSI is at seal level and 40 psi at elevation...

    40 PSI is at seal level and 40 psi at elevation are two different things. If our starting absolute is 11.9PSI at elevation 51.9psi absolute would be 40 psi above it. But at sea level if our starting...
  5. Replies
    14
    Views
    283

    Yes your truck will compensate for fuel pressure...

    Yes your truck will compensate for fuel pressure correctly if you don't touch the PW table. That's why your PW table is Pressure vs MM3, it's also why i don't mess with that table because it throws...
  6. Replies
    14
    Views
    283

    That's good to hear, you'll also notice the truck...

    That's good to hear, you'll also notice the truck switches timing and fuel pressure maps at idle after a little bit of no input on either the gas or brake pedals. I don't know if it's the same map on...
  7. Replies
    14
    Views
    283

    Here is my timing map that will see 21* during...

    Here is my timing map that will see 21* during pulls. It took me a while to get my timing to ramp up smoothly and this is the 3d view of it which actually helps a lot with understanding why. 93457
  8. Replies
    14
    Views
    283

    Did you hit your commanded fuel? If you're...

    Did you hit your commanded fuel? If you're hitting your target fuel set in your tq2fuel map, i don't think you'd get richer by lowering the limiter as it's not in effect just yet, That is my...
  9. Replies
    14
    Views
    283

    Check your smoke limiters. What are they set to?...

    Check your smoke limiters. What are they set to? Let's break down all the ways these trucks can get fuel added. I know you can add fuel by increasing torque to fuel quantity. You can also add...
  10. Replies
    8
    Views
    303

    what's your boost doing? Data log it and send me...

    what's your boost doing? Data log it and send me your log.
  11. Replies
    8
    Views
    303

    There is a reason for the negative timing values...

    There is a reason for the negative timing values in the cruise region, you can smooth it out but you'll notice something change as you up it. Pay attention and you'll notice it.
  12. Replies
    8
    Views
    303

    Throw that thing in the garbage, timing calcs are...

    Throw that thing in the garbage, timing calcs are a waste of time, their only use is a quick reference of where you're currently at for piece of mind, more so for data to see potential trends. That...
  13. Replies
    2
    Views
    190

    They are fault codes and they each do different...

    They are fault codes and they each do different things. One can trigger reduced engine power and one might trigger reduce engine power, but only reduce the power by X amount instead of X amount. If...
  14. Replies
    20
    Views
    1,192

    Mine is doing something very similar. It also...

    Mine is doing something very similar. It also started after the update. Fails first flash on my 2018 f-250 then i retry and it works, It'll fail every time almost on certain USB ports but one is...
  15. Replies
    16
    Views
    3,079

    Can you Post your tune so i can look at it and...

    Can you Post your tune so i can look at it and see if there's a issue? It might be that you increased it outside of the parameter limits which creates the problem.
  16. Replies
    16
    Views
    499

    This is the best piece of advice for timing. I...

    This is the best piece of advice for timing. I have tried used timing calculators and values that big tuners use on a stock truck and swear by with absolutely awful results, there's just too many...
  17. :cheers:

    :cheers:
  18. Holy wow wow wow, I'm not a dodge guy but that...

    Holy wow wow wow, I'm not a dodge guy but that looks like pretty poor fueling control. It's almost setup like a light switch for fueling, on or off no in-between lol. I'd love to see a stock file,...
  19. Replies
    2
    Views
    177

    Create a ticket with support.

    Create a ticket with support.
  20. That doesn't sound like it's a proper delete...

    That doesn't sound like it's a proper delete tune, did you do it yourself? Do you have any post injection events actually happening while this message is being displayed?
  21. Replies
    1
    Views
    147

    92373 These tables will need adjusting. Do you...

    92373 These tables will need adjusting. Do you have a data log of this happening by chance?
  22. Replies
    8
    Views
    738

    I'm having the same issue with it failing mid...

    I'm having the same issue with it failing mid flash consistently saying timed out. But mine was tune related, or so i had thought. Some tunes were fine and others weren't, i had tunes i knew i...
  23. Are they elevation based tables?

    Are they elevation based tables?
  24. I'm not a cummins guy but it appears to be doing...

    I'm not a cummins guy but it appears to be doing exactly as it's commanded to do IMO. Look at your ECM 7411 table. It's following that table perfectly. Your truck goes up to 19* when part throttle...
  25. Replies
    16
    Views
    3,079

    Did you change anything related to the tire size...

    Did you change anything related to the tire size or try re-calibrating the speedometer?
Results 1 to 25 of 96
Page 1 of 4 1 2 3 4