Search:

Type: Posts; User: GapRider

Page 1 of 10 1 2 3 4

Search: Search took 0.00 seconds.

  1. Really appreciate your feedback! wideband shows...

    Really appreciate your feedback!
    wideband shows dithering around lambda 1 at cruise so i feel like I'm good there, right?

    but I looked at SOI, you're right!, low load is the same as hi load, I...
  2. GREAT thread and great help here - it's what I...

    GREAT thread and great help here - it's what I used to tune my Gen V for headers, cam, with DOD and VVT delete!
    Love the choppy 900RPM idle, never stalls, WOT always 99.6% throttle and spark where I...
  3. Replies
    22
    Views
    2,245

    I just got back from camping, thank you both...

    I just got back from camping, thank you both (Ghuggins and TriPinTaz) so much for all this info. I started with trying a stock VE/VVT version but all I can do is idle in the garage because it's...
  4. Replies
    4
    Views
    1,254

    That is awesome, always great when the smoking...

    That is awesome, always great when the smoking gun is found
  5. Replies
    4
    Views
    1,254

    Scoggin Dickey says the pumps have an electrical...

    Scoggin Dickey says the pumps have an electrical device (solenoid?) that fails to high pressure. I just did the same DOD delete on mine with Texas speed valley cover and what not, are you sure you...
  6. Replies
    22
    Views
    2,245

    BTW, I had a hard time doing a full write because...

    BTW, I had a hard time doing a full write because the car kept going to sleep before the tune had fully written. It finally worked when I hit the 'start' button on the car as soon as it went to sleep...
  7. Replies
    22
    Views
    2,245

    man there's so much there but it helps me to see...

    man there's so much there but it helps me to see it. I still don't know what you mean when you say 'density' , I just know VVE (which is speed density I thought) and VT (torque).
    I did read in...
  8. Replies
    22
    Views
    2,245

    thanks so much GHuggins, I'm going to try it and...

    thanks so much GHuggins, I'm going to try it and I've got some reading to do now before I post back. Again, thanks so much.

    BTW, I could open the tune but not the log (please update your software)...
  9. Replies
    22
    Views
    2,245

    That someone is me :). I?m learning and really...

    That someone is me :). I?m learning and really appreciate the insight. The tune is based heavily on a post that compiled changes made for cam and headers, really helpful. I?ve done other things trial...
  10. Replies
    22
    Views
    2,245

    Well I've changed all DFCO, TQ acc/dec stuff back...

    Well I've changed all DFCO, TQ acc/dec stuff back to the tune I ran when I just had headers but still get the CEL for P015B,D (freeze frames always show 34.75 STFT).
    I finally got the situation on a...
  11. Replies
    2
    Views
    689

    thanks so much for your insight, more to think...

    thanks so much for your insight, more to think about.
    Your 1.5 turns is another relatable data point for me as mine are at 1.25 turns.
    With the M8 rocker bolt with 1.25mm pitch and a 1.8 rocker...
  12. Replies
    2
    Views
    689

    0.100" preload Caddy Race Lifters?

    I have searched, read, called and I only see one reference to the recommended preload for Caddy Race lifters which I installed with my CAM MOTION cam - 0.050" to 0.100" on the BTR website.
    I read...
  13. Replies
    22
    Views
    2,245

    Man, great to know, thank you! I'm pretty sure...

    Man, great to know, thank you!
    I'm pretty sure both my Virtual Torque and Virtual Volumetric Efficiency models are off (both are just calculated from stock based on diff in dyno numbers for stock...
  14. Replies
    22
    Views
    2,245

    glad to see your response. Sounds really similar...

    glad to see your response.
    Sounds really similar after my cam install with headers. 34.75% STFT shown on Freeze frames for CELs but otherwise rich cuz my airmodel needs adjusting. No rear O2s for me...
  15. Replies
    1
    Views
    652

    I'm not a tuner, just a learner with my own car....

    I'm not a tuner, just a learner with my own car.
    I've learned alot from this board and this guy is really helpful
    https://goatropegarage.com/
  16. Cam tables zero at idle but I still see 4 degrees?

    I zeroed out my cam tables at idle but I still see ~4 degrees cam position at idle sometimes.
    I set all ECT correction multipliers to 1.
    I can't find anything else in the tune that does not tell...
  17. Replies
    0
    Views
    387

    LT1 stock hpfp bore and stroke?

    Does anyone know the bore and stroke of the stock LT1 HPFP?
  18. I hope it's OK if I jump in with a question also...

    I hope it's OK if I jump in with a question also because I'll soon install a cam with larger fuel lobes. (I know it's an old thread)
    Fundamentally, the larger fuel lobe strokes the positive...
  19. Replies
    7
    Views
    3,528

    here's the tune and log

    here's the tune and log
  20. Replies
    7
    Views
    3,528

    I'm not having success with System/Fans/Vehicle...

    I'm not having success with System/Fans/Vehicle Speed Adjust - fan % logged seems to ignore it.
    Any suggestions, right now I'm stumped?

    118541118542
  21. Replies
    231
    Views
    153,471

    An example of what it sounds like...

    An example of what it sounds like https://youtu.be/sPaI-dknKZg
  22. Replies
    7
    Views
    1,926

    That's the one I have coming too.

    That's the one I have coming too.
  23. Replies
    231
    Views
    153,471

    the cam tune just mimicks the valve overlap of...

    the cam tune just mimicks the valve overlap of old school big cams so no danger to the engine but you end up with lots of unburned fuel in the exhaust. Nobody ran cats back then so no issue but now...
  24. Replies
    231
    Views
    153,471

    Ethan, I sold the car a couple of years ago and...

    Ethan,
    I sold the car a couple of years ago and the specifics have just faded, I'm sorry.
  25. Thank you sir!

    Thank you sir!
Results 1 to 25 of 247
Page 1 of 10 1 2 3 4