Search:

Type: Posts; User: Kmoney

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    2,150

    If you don't have a scan tool that will actuate...

    If you don't have a scan tool that will actuate the pump, You can "disconnect" the Lin bus wire from the pump with ignition on. It should run 100 percent. Wire should be white with brown trace.
  2. Replies
    15
    Views
    3,881

    Im going to inbox you my number

    Im going to inbox you my number
  3. Replies
    15
    Views
    3,881

    Skim will not cause a no crank. Do you have 12...

    Skim will not cause a no crank. Do you have 12 volts at the starter main battery led? If you apply 12 volts to the solenoid does it crank?
    You can inbox me. I can probably get you going.
  4. Replies
    21
    Views
    10,082

    Reading your post looks just like mines back when...

    Reading your post looks just like mines back when I started out. MY car had no symptoms other than a periodic check engine light. Try running off one Ve Table. If it still pops up it is mechanical...
  5. Replies
    21
    Views
    10,082

    Before you go messing around with the tune for...

    Before you go messing around with the tune for this, I would do a smoke test. I had this very issue for a year after my supercharged 6.1 build and found my intake gasket on bank 1 was blown out by...
  6. Replies
    4
    Views
    1,347

    Sounds like you just need the vin programmed in...

    Sounds like you just need the vin programmed in the pcm..
  7. Replies
    3
    Views
    3,904

    It starts are rear wheel abs sensors to abs...

    It starts are rear wheel abs sensors to abs module then can bus to PCM and TCM.
  8. Replies
    3
    Views
    3,904

    Gonna need an abs module to get a speed sensor...

    Gonna need an abs module to get a speed sensor signal.
  9. I would look at turning them all off in the tune.

    I would look at turning them all off in the tune.
  10. Replies
    2
    Views
    1,282

    He is correct. That table is there to make...

    He is correct.


    That table is there to make the out computers in the car happy. It has to match the original config or you will get implausibility codes. Setting it to 5.7 won't effect...
  11. Replies
    9
    Views
    5,075

    Yes PCS table. I've been struggling with the lock...

    Yes PCS table. I've been struggling with the lock up. There is a file that 300c made that has the tables conversions that help with lockup times.
  12. Thread: Misfire P0300

    by Kmoney
    Replies
    19
    Views
    7,755

    borescope time.

    borescope time.
  13. Replies
    9
    Views
    5,075

    I lower {raised numbers} line pressure in the...

    I lower {raised numbers} line pressure in the lower areas to calm down my downshifts.
  14. Replies
    23
    Views
    16,366

    yes

    yes
  15. Replies
    23
    Views
    16,366

    PCM will work but you will need to program the...

    PCM will work but you will need to program the vin and make a few changes with hptuners. harness shouldn't be needed.
  16. Replies
    3
    Views
    1,693

    Probably gonna have to modify the tbody to close...

    Probably gonna have to modify the tbody to close it more while getting the tps voltage up a few more tenths. or you have a vacuum leak somewhere.
  17. Have you verified fluid level? Mak sure its not...

    Have you verified fluid level? Mak sure its not over filled. 2-1 down shift may be the issue. try moving that around a bit to see if it makes a difference. Im the same way. I dont drive it enough to...
  18. Replies
    4
    Views
    2,763

    Get rid of that thing.. they are terrible..

    Get rid of that thing.. they are terrible..
  19. lets see the tune?

    lets see the tune?
  20. What do you have for a fuel system? Tell us about...

    What do you have for a fuel system? Tell us about the build.
  21. Replies
    13
    Views
    4,795

    All that can be changed..

    All that can be changed..
  22. Replies
    2
    Views
    1,528

    I use the ford 80 pounders with my magnuson. they...

    I use the ford 80 pounders with my magnuson. they are taller so I use rail spacers.
  23. Replies
    5
    Views
    2,051

    plugged cats....

    plugged cats....
  24. Replies
    2
    Views
    881

    Are you looking at the pedal percentage or the...

    Are you looking at the pedal percentage or the actual Tbody. Anything over 75 percent for Chrysler is considered WOT. But as always.... Post the tune and log..
  25. Replies
    19
    Views
    15,578

    I agree. I have a protorque 2800 I my car is...

    I agree. I have a protorque 2800 I my car is undriveable with the convertor unlocked in 1 and 2.
Results 1 to 25 of 117
Page 1 of 5 1 2 3 4