Search:

Type: Posts; User: Jarrod.v

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    338

    Anyone???

    Anyone???
  2. Replies
    2
    Views
    249

    Try repolling for vehicle a couple times. You...

    Try repolling for vehicle a couple times. You might also try resyncing the interface too. I had this same issue last week, and doing the repoll and resync got everything working again.
  3. Replies
    3
    Views
    338

    I had to raise the VT tables because it was...

    I had to raise the VT tables because it was limiting the delivered torque. I will upload the log file that showed where the torque was just a straight line, and wouldn't get any higher (despite the...
  4. Replies
    3
    Views
    338

    600 lb ft Torque

    Once again, I am getting insanely high torque values. I have it in closed loop, and it is still reading 607 lb ft of torque at 4800 rpm. As much as I would love to believe that these values are...
  5. Replies
    20
    Views
    1,297

    Just bought Engine Management: Advance Tuning two...

    Just bought Engine Management: Advance Tuning two days ago! Almost to chapter 7 lol
  6. Replies
    4
    Views
    376

    If you force PCM into Open Loop, are the narrow...

    If you force PCM into Open Loop, are the narrow bands still being used to make calculations? I am asking because I did remove the B1S1 narrowband to temporarily install the wideband to make...
  7. Replies
    8
    Views
    354

    I swapped back over to Closed Loop, fixed the VE...

    I swapped back over to Closed Loop, fixed the VE tables, and took her for a spin. I got the LTFTs within (+/- 1) of 1 lambda. The torque logs basically match up from everything under .76 grams of cyl...
  8. Replies
    8
    Views
    354

    I definitely did not do that :doh: ... I am...

    I definitely did not do that :doh: ... I am assuming that it would be best to just start back at square one, and then go from there? What is the best way to properly learn all this stuff, besides...
  9. Replies
    8
    Views
    354

    Before logging anything, I modified the VVE...

    Before logging anything, I modified the VVE zones. In doing so, it recalculated all the coefficients. Now I have been in the process of getting the VVE dialed in. I know that the current log shows...
  10. Is turning desoot off beneficial? I know this is...

    Is turning desoot off beneficial? I know this is completely off topic from the OP lol
  11. Replies
    8
    Views
    354

    I just installed that AEM wideband after the cam...

    I just installed that AEM wideband after the cam swap. I did a free air calc on it too. It should be reading correctly, but I'll check the logs in CL tomorrow. I definitely did not think that the log...
  12. Replies
    8
    Views
    354

    Are these torque logs accurate?

    I know HP Tuners is fairly close when it comes to logging torque, but how close? I feel like these numbers shouldn't be this high. The truck is an 09 2500 HD with the LY6. Added a Sloppy Stage 2...
  13. Replies
    4
    Views
    284

    Made your two changes as stated above, and the...

    Made your two changes as stated above, and the truck is running great! I appreciate the help
  14. Replies
    17
    Views
    847

    Literally had the same similar issue today except...

    Literally had the same similar issue today except I am in SD only. Did your maro throw any codes? I generated a P0106 and P0068. Had some insight from others and suggested to raise a couple...
  15. Replies
    4
    Views
    284

    I will make those changes and see what it does! I...

    I will make those changes and see what it does! I really appreciate everyone's help on here.

    Question. Why would I need to make those changes on this truck, but I never changed those parameters...
  16. Replies
    4
    Views
    284

    HELP! Reduce Power Mode

    Truck will start up and idle great. I take off diving, and everything is running fine until I get a couple miles down the road. It goes into reduce power mode, and I can see on the scanner that I am...
  17. Replies
    1
    Views
    296

    Can't find LTIT, Idle Air and others

    I have a 2009 LY6 Gen 4 E38. I am trying to load all the channels for the Russ K's idle config, and I don't have Idle Desired Airflow, Idle Air Control Desired Position, Idle Air Control Position,...
  18. Replies
    4
    Views
    277

    I wasn't able to check the editor out at that...

    I wasn't able to check the editor out at that moment, but I was able to change it out and read what it applied to. Thanks for the info though! I'll give an update on the truck later this afternoon...
  19. Replies
    4
    Views
    277

    Thanks for the quick reply! I will make that...

    Thanks for the quick reply! I will make that change, but can you explain what that will fix please
  20. Replies
    4
    Views
    277

    RPM drop from idle to drive/reverse

    I installed a Trick Flow 3062003 cam into this LY6 block. I got the idle in range enough to do initial "break-in", and do some driving around in it. I tuned the MAF up to 4000RPM and its about 3%...
  21. Replies
    17
    Views
    847

    It's all good. I'm here constantly learning new...

    It's all good. I'm here constantly learning new things too. Between here and youtoube, we will all become experts though :cheers:
  22. Replies
    17
    Views
    847

    lol thats what i said to do on the very first...

    lol thats what i said to do on the very first reply...
  23. There's an EQ ratio table under Engine-Fuel-Power...

    There's an EQ ratio table under Engine-Fuel-Power Enrichment. Check that out and see if that's what you're looking for
  24. Replies
    6
    Views
    738

    You're awesome! Thank you for the help!

    You're awesome! Thank you for the help!
  25. Replies
    6
    Views
    738

    Thanks! I assume that the same concept would...

    Thanks! I assume that the same concept would apply if it's going to be suited for primarily towing? Just leave it and make the rest of the changes with the other setting? Also, do I leave power...
Results 1 to 25 of 37
Page 1 of 2 1 2