Search:

Type: Posts; User: Eleazer2

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    9
    Views
    943

    I got Engine RPM and speed working from the HP...

    I got Engine RPM and speed working from the HP tuners CAN output but I found a issue in HP tuners if I try to pull MAP or lamda into my dyno
    HP tuners is only sending whole numbers for example vcm...
  2. Replies
    9
    Views
    943

    I'm having a similar issue. I have a MPVI2 with...

    I'm having a similar issue. I have a MPVI2 with the pro link and i have a CAN interface from my Mustang Dyno. i setup the CAN output in HP Tuners VCM scanner and set the data to Engine rpm but in my...
  3. Replies
    51
    Views
    6,398

    I had the same issue with a 2015 Mustang GT that...

    I had the same issue with a 2015 Mustang GT that was auto swapped it had a 80mm single turbo. It would run fine on the streets but at the track on a hard pull the throttle would just shut and it...
  4. Replies
    2
    Views
    791

    Thanks!

    Thanks!
  5. Replies
    2
    Views
    791

    2018+ F150 Whipple Stage 1 read

    Does anyone have a 2018+ F150 Stage 1 Whipple tune file i can look?
  6. Replies
    2
    Views
    3,763

    Did you ever figure the issue out?I had a similar...

    Did you ever figure the issue out?I had a similar issue with a single turbo 2015 Mustang GT that was swapped to a 6R80. The throttle would shut off at exactly 63-67mph when making a hard pass at the...
  7. Veefour I seen a post on the forum about a user...

    Veefour I seen a post on the forum about a user that had a 2019 Mustang GT and it was throwing a hill assist error and causing some more issues, he said the fix was to use the scanner to make the...
  8. Eric what about the N/V Base?

    Eric what about the N/V Base?
  9. Changing Tire Size and Rear Gear Ratio on 2015 Mustang GT

    I looked on the forum about changing the gear ratio and tire size and I get conflicting info. Can you change this in VCM Editor to Calibration instead of Learn from BCM or do you leave the switches...
  10. Replies
    19
    Views
    18,979

    I’m hitting a Transfer case limit that it...

    I’m hitting a Transfer case limit that it floating the throttle completely on a 2015 Mustang 6R80 any help on what I need to change. I’ve already have the gears set to 8,500 rpm and raised max torque...
  11. ETC Torque Request maxed out at 738ft lbs

    I have a 2015 Mustang GT Clip/add torque is turned off however i noticed under WOT my ETC hits 738ft lbs I will get Torque reduction Driver Demand and my throttle will close 3.5 degrees until ETC...
  12. Ok I think I got the throttle issues solved I can...

    Ok I think I got the throttle issues solved I can see ETC torque requesting more now however I am now hitting a throttle angle source limit TQ Reduction Driver demand it seems to hit it every time my...
  13. Thanks guys any ideas on the Torque management...

    Thanks guys any ideas on the Torque management issues you think that is causing the problems with the ETC torque request being so low?
  14. if I'm thinking right would I just create a math...

    if I'm thinking right would I just create a math function and do aem pressure sensor + 14.7
  15. Murfie can you tell me how I can adjust the...

    Murfie can you tell me how I can adjust the sensor so I can make it read absolute the formula it comes predefined with shows (V/0.08) =+ -20.95=output psi


    I actually had load at WOT set to air...
  16. Any ideas on how to solve or any guidance you can...

    Any ideas on how to solve or any guidance you can give me
  17. Murfie since I moved my pressure sensor behind...

    Murfie since I moved my pressure sensor behind the TB now I can see vacuum and boost however if I use the speed density calculator in hp tuners I just see boost pressure why would I need to see...
  18. I’m trying to run around 18 psi of boost the...

    I’m trying to run around 18 psi of boost the pressure sensor I was using was mounted in the charge pipe right before throttle body i since moved it to the intake behind TB so I can get a accurate...
  19. What limit am i hitting its not showing up in log

    2015 Mustang GT with a single 80mm turbo, 2018 intake, IMRC Deleted. Car runs fine on the street but at the track sometimes it will close the throttle completely and if you raise you foot off the...
  20. Open up your scanner and go to Vehicle tab at top...

    Open up your scanner and go to Vehicle tab at top of screen and select Repoll make sure you connect to the vehicle first or it will be grayed out. Try that and see if it works
  21. Need help seeing why my car loses power at the drag strip

    I have a 2015 Mustang GT with a 80mm single turbo car runs great on the road and first pass off the trailer at the 1/4 drag strip however after I finish the first pass I shut the car off waited close...
  22. Replies
    4
    Views
    1,575

    I think I figured it out I will see once I’m back...

    I think I figured it out I will see once I’m back at the drag strip
  23. Replies
    4
    Views
    1,575

    I don’t see torque errors based on my log file...

    I don’t see torque errors based on my log file the torque error shows 0 I currently have the max error set to 75,000
  24. Replies
    4
    Views
    1,575

    2015 Mustang GT dead pedal on drag strip

    Having a issue and wanted to see if anyone could help out. Car is a 2015 Mustang GT single turbo it made 1 pass and I upped the spark by 2 degrees and increased the boost controller by 1psi and every...
  25. Replies
    19
    Views
    12,765

    Did you ever get this fixed? i'm thinking about...

    Did you ever get this fixed? i'm thinking about doing the same with my car
Results 1 to 25 of 108
Page 1 of 5 1 2 3 4