Search:

Type: Posts; User: VXSS

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    11
    Views
    1,159

    Can anyone tell me if the maf tables are...

    Can anyone tell me if the maf tables are referenced even with no maf connected running olsd? This thing just refuses to pull fuel at decel at times. Can get down into the 10s seems to be inconsistent...
  2. Replies
    11
    Views
    1,159

    I will give it a shot. Thanks

    I will give it a shot. Thanks
  3. Replies
    11
    Views
    1,159

    I'm trying to reduce a rich decel. I have dropped...

    I'm trying to reduce a rich decel. I have dropped the minimum pulswidth under the fuel tab and its not too bad but I'm sure in the past I have adjusted the transient - min fuel milligrams also
  4. Replies
    11
    Views
    1,159

    Hmm I'm so sure I have adjusted this before in...

    Hmm I'm so sure I have adjusted this before in gen 4s
  5. Replies
    11
    Views
    1,159

    My view is set to advanced. So nobody else has...

    My view is set to advanced. So nobody else has this issue?
  6. Replies
    11
    Views
    1,159

    Transient - min fuel milligrams

    Am I the only one that can't access the min fuel mg under the transient tab? I have updated to the latest version and it isn't showing for any tune file.... I'm sure I'm not imagining it being there
  7. Im having a hard time finding out for sure... but...

    Im having a hard time finding out for sure... but is the PCM modification service needed for a 2015 ecodiesel Grand Cherokee?
  8. Replies
    8
    Views
    2,842

    So it turns out that clutch sensor fitted switch...

    So it turns out that clutch sensor fitted switch does exist and hptuners added it for me. So now I can get the clutch status to change but unfortunately still no dfco. Seems like even though it's...
  9. Replies
    8
    Views
    2,842

    Yes it does unfortunately. I was afraid that...

    Yes it does unfortunately. I was afraid that might be the case.
    How are people getting their dfco working with manual swaps? It seems to default to clutch in the depressed position
  10. Replies
    8
    Views
    2,842

    I know this is a very old thread... but I'm...

    I know this is a very old thread... but I'm trying to get the clutch switch to work on an e67 from an enclave v6. I have tried feeding it 12 volts, 5 volts, earth 1.5 volts to the clutch position...
  11. Replies
    5
    Views
    6,066

    Sorry I missed the reply. Yeah running 98 but...

    Sorry I missed the reply. Yeah running 98 but have not made any changes to the tune yet. I feel like the diff ratio of 3.45 with the t56 isn't helping
  12. Replies
    5
    Views
    6,066

    I'm only NA in this beater for the time being....

    I'm only NA in this beater for the time being. Possibly I'm expecting too much from it. I'm getting a few degrees Kr at low rpm so maybe there is not much to gain without better fuel anyway
  13. Replies
    5
    Views
    6,066

    Advancing cams at low rpm for torque?

    Has anyone had success with advancing cam timing for more low rpm torque? I have read that hptuners does not have all the required tables, is this true? Would love to pickup some bottom end power. ...
  14. Replies
    7
    Views
    6,112

    Sounds like an interesting project. Cheers

    Sounds like an interesting project. Cheers
  15. Replies
    7
    Views
    6,112

    I know this is an old thread but what did you use...

    I know this is an old thread but what did you use for a crank angle and cam angle sensors with the sohc? Is it possible to use the au crank angle sensor inplace of the distributor?
  16. Thread: P2101 Threshold

    by VXSS
    Replies
    3
    Views
    2,148

    Hmm thats what i thought. Its not there

    Hmm thats what i thought. Its not there
  17. Thread: P2101 Threshold

    by VXSS
    Replies
    3
    Views
    2,148

    P2101 Threshold

    Can anyone tell me where to find the P2101 settings? i cant find them anywhere. Do i need to request it to be added?
  18. Yeah i dont need to change anything over 1000rpm...

    Yeah i dont need to change anything over 1000rpm and im hoping that the low amount torque produced at low rpms 25 to 30nm at idle is not going to stress the trans. Has completely changed the car and...
  19. Is the torque model editing function only for gen...

    Is the torque model editing function only for gen 5 ecms? I have an e38
  20. Lowering torque coefficents fixed my CT Downshifts

    Since putting in a small cam in my 08 caprice L98 with a 6l80e i have had really crappy closed throttle downshifts. It would pull way too much timing causing hesitation and lurching and also making...
  21. Thread: Injector tuning

    by VXSS
    Replies
    30
    Views
    17,423

    Coming back over to this side of the forum makes...

    Coming back over to this side of the forum makes me happy i went back to an LS engine lol
  22. Replies
    1
    Views
    1,605

    Im interested in this also. No news?

    Im interested in this also. No news?
  23. Replies
    11
    Views
    4,951

    Cool I will have to update

    Cool I will have to update
  24. Replies
    11
    Views
    4,951

    What mods are done to the car? Generally the...

    What mods are done to the car? Generally the speed density doesnt need to be touched unless you have different camshafts or something like that. Just put your narrow band back in and clear the fuel...
  25. Replies
    11
    Views
    4,951

    At cruise and idle you should be in closed loop...

    At cruise and idle you should be in closed loop using the stft and ltft to keep you at stoich 14.7afr. What kind of wideband are you using? Have you still got the stock narrow band o2 plugged in?
    ...
Results 1 to 25 of 54
Page 1 of 3 1 2 3