Search:

Type: Posts; User: Hendonjt81

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    658

    VCM Scanner Data

    I?m tuning a Gen3 5.3L with a 102mm tb and sheet metal intake.

    When tuning VEvsLTFT and MAFvsLTFT my graphs only populate data in the first column.

    Data received seems within normal range for...
  2. Replies
    11
    Views
    3,577

    5FDP....injectors! I had an issue on initial...

    5FDP....injectors!

    I had an issue on initial startup where several injectors were frozen...
  3. Replies
    11
    Views
    3,577

    Ok, Fuel Pressure Key on - 45psi Fuel...

    Ok,

    Fuel Pressure Key on - 45psi
    Fuel Pressure Started - 56-58psi

    O2 Harness cannot be swapped since Bank 2 runs along side trans harness.

    I pulled/cleaned MAP, TB, and did a relearn.
    ...
  4. Replies
    11
    Views
    3,577

    Thanks! I made a minor adjustment to the VVE...

    Thanks! I made a minor adjustment to the VVE table to assist with idle. The tuning guide I'm using instructs to enable MAF only mode while idle tuning. I'm running 340lph pumps in each tank. Key on...
  5. Replies
    11
    Views
    3,577

    Thanks RobZL1. I'll read the post. I have the...

    Thanks RobZL1. I'll read the post. I have the tune dialed in until I hit 133*. Upon restart, the engine revs.
  6. Replies
    11
    Views
    3,577

    New Scan

    5FDP,

    Adjusted tune last night and addressed LTFT at idle via Virtual VE (among other issues previously discussed). The permanent codes will require drive time to clear (specifically P2138). I'm...
  7. Replies
    11
    Views
    3,577

    Thanks again, I?m following a ?Tuning Guide? that...

    Thanks again, I?m following a ?Tuning Guide? that doesn?t go into depth. I noticed the VVT/DOD after last post.

    With respect to Fuel pressure, if it?s lower than 58psi do I need to rescale...
  8. Replies
    11
    Views
    3,577

    5FDP, I was tracing down an idle problem and...

    5FDP, I was tracing down an idle problem and missed a few SES deactivations when starting over.

    I currently have MAF off, no rear o2's, all EVAP deleted, the 340x codes needed to be...
  9. Replies
    11
    Views
    3,577

    VCM Scanner Interpretation

    New to tuning. I'm Idle tuning on a Gen IV E38. I've adjusted idle air/RPM and spark.

    When interpreting the log file...

    How do you know idle air is correct? I'm seeing .26-.30g Cyl Air mass.
    ...
  10. Thread: E38 p0606

    by Hendonjt81
    Replies
    1
    Views
    1,221

    Did you figure this out? I'm experiencing a...

    Did you figure this out? I'm experiencing a similar issue with the P0606
  11. Replies
    1
    Views
    968

    e38 No Start

    Before I get too far in the weeds here....

    2010 5.3L/6L80, e38 (LS swap 85' C10)

    VATS 1, 2, and Starter Fault disabled.

    I have 52psi fuel pressure and good crank signal - Scanner shows rpm...
  12. Replies
    3
    Views
    1,512

    The Silverado pedal won?t clear trans tunnel in...

    The Silverado pedal won?t clear trans tunnel in 73-87? C10?s.

    Most guys run the Camaro or Diesel pedal and swap pinouts.

    Can the pedal cal files from 2010 Camaro be placed in...
  13. Replies
    3
    Views
    1,512

    P2138/Evap Codes

    Long time stalker, first time poster. Need some guidance on a recent personal swap.

    2010 Silverado 5.3L/6l80 (Standalone harness/e38 ecm).
    2010 Camaro Pedal (pins D/F swapped)

    Verified the...
Results 1 to 13 of 13