Hey guys I have a 2020 L86 and E92/ T87a setup in a 77 C10. I cannot get the ECM to send 12V to the fuel pump relay. So far I've disabled VATs and disabled Starter Diag. Is there anything else...
Type: Posts; User: lxcoupe
Hey guys I have a 2020 L86 and E92/ T87a setup in a 77 C10. I cannot get the ECM to send 12V to the fuel pump relay. So far I've disabled VATs and disabled Starter Diag. Is there anything else...
Hi wondering what the difference between an MPVI2 with a Pro Link cable and the MPVI2 Pro? I assume there's a firmware difference between the two and if so can I pay to update my firmware?
I'm...
I just bought an nGauge and was wondering if I can use it to tune all the vehicles associated with my MPV-1?
Still fixed?
Did you resolve this?
There are two methods of powering the flex fuel sensor... 12V key-on (cuts 12V while cranking) and 12V ignition on (keeps 12V while cranking). Is it mandatory that the sensor maintain 12V during...
So I have a basic n/a 416 with a small cam using all LS3 sensors including stock LS3 injectors, LS3 MAF, etc. I plan to start with an L99 Camaro base file and I just need to get this thing started...
Hey guys, I have a 2018 Express Van 6L90e. Having a harness built and I don't have a PCM yet. I'd rather not remove the TCM from the trans if I can avoid it, so any guidance as to which OS I can...
Seeing if you figured this out? I also just obtained a 2018 Express Van 6L90e for my swap project.
Is that done through VCM editor or the forum?
Are the '19 Camaro A10's currently supported?
I completed a 5.3/T56 swap in a 2006 Chevy Colorado using a E67 PCM from a 2006 Cadillac CTS-V. Is it possible to write my original VIN onto the E67 PCM? The Colorado originally ran OS # 12593533
I'm doing an LS3/4L80e swap in an old C10. I know I need an E38 ECM/ T42 TCM. A good place to get this combo is a 2008-2009 Express Van or 2008-2009 Silverado. I'll be buying them used, individually....
I'm doing an LS3/4L80e swap in an old C10. I know I need an E38 ECM/ T42 TCM. A good place to get this combo is a 2008-2009 Express Van or 2008-2009 Silverado. I'll be buying them used,...
Hey guys, wondering if someone can explain something to a newb. I have a set of factory LS3 injectors modified by FIC to flow 60LB. What, if anything, is changed in a base tune so that the vehicle...
Thanks, where'd you find that file? It's nearly identical to a stock file from the looks of it.
Hey guys, just got my swap running... an 89 Dodge Dakota Shelby with an 03 Yukon 5.3, 4L60e, stock manifolds, true duals with no cats, and an eBay cold air intake. I've found a few 4L60 articles,...
Hey guys, I'm running a 2005 Avalanche flex fuel OS on my 2005 Silverado. I've paid for both licenses and they both show up in my licenses list. But when I read the Avalanche OS off my truck, then...
I seem to have resolved this by comparing tunes in the tune repository to my own. The "Desired Throttle Area" table was really aggressive, I copied over several tables from other E38 turbo trucks...
Hey guys, I have always experienced an extremely sensitive throttle on my turbo charged 05 Silverado. Stock throttle body, and no other issues. I can step on the gas and it's very touchy, and if...
So I've transferred everything over besides "Offset vs. Press vs. IGNV", still not sure what to do about that table.
I've read that there are 5 various parameters that need to be modified in order to properly control the injectors. I am trying to copy over the injector data from a LC9 flex fuel Avalanche tune over...
Thank you, I must have the right cam gear installed them.
All else being in order, if a 58x Gen IV motor had an LS6 cam installed and the installer used a 1x cam gear instead of a 4x, would the motor even start?
Hey all, I have a 2006 Colorado with a LC9 5.3L (58x) that we did the dod and afm delete and installed a LS6 cam, LS6 intake, and headers. I used the LC9 36LB flex fuel injectors from the truck...