Search:

Type: Posts; User: Eli R. Morales

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    893

    Firm shift on GenV

    Hello everyone, Can someone give me the recipe or guide me on how to completely disable the spark and fuel cutoff that the GenVs do when they shift, I don't care if the transmission breaks into 2...
  2. Replies
    4
    Views
    1,237

    114739114739 Apparently there are problems...

    114739114739 Apparently there are problems uploading files I could barely upload my tune when I can send the log too, I did not make a good correction in the sd or maf, the headers are free with...
  3. Replies
    4
    Views
    1,237

    Big cam idle tune problems

    Someone with experience can help me or give a reference on how to adjust the startup and that the idle is stable after starting the engine with a 6.0 224/244 112 cam and worked heads, the problem is...
  4. Replies
    3
    Views
    1,302

    I thought so but apparently it's not like that,...

    I thought so but apparently it's not like that, or I don't know if I have any mistakes, because it happened to me in several cases in both 3gen and 4gen

    95851
    95852
  5. Replies
    3
    Views
    1,302

    5.3 to 6.0 swap idle problem

    Hello everyone, what may be happening when I have a 5.3 pc and I convert it to 6.0 through a tune or a segment swap with the hp tuners, it has happened to me on several occasions that I start the...
  6. The only thing I can tell you is "forget...

    The only thing I can tell you is "forget everything"

    The engines of the LS and LT series are similar but not the same, their operation and constructions are totally different
  7. Replies
    2
    Views
    2,199

    Good points to start, thanks

    Good points to start, thanks
  8. Replies
    2
    Views
    2,199

    Guidance for Ford diesel

    Hello everyone, I am looking for information on the basics of diesel tuning, it will be my first time that I have to tune a diesel ford and to be my first time I want to do a good job, any basic...
  9. Replies
    1
    Views
    2,363

    Mustang 4.6 3v

    Hi guys, I have very little experience on Ford ECUs, but my work has led me to tune into the first mustang 4.6 3V MT. Stock, since I do not know how it behaves and what is it that this car likes, I...
  10. This has already been proven? It works well? I do...

    This has already been proven? It works well? I do not have much time to experiment
  11. l96 flex fuel injectors on gen 3 pcm, help

    Hi guys, has anyone used the injectors of a 6.0 l96 flex fuel engine finish at 3412 (50 lb / h), on a PCM Gen 3? I would like someone to help me with all the data in the control of the injector,...
  12. Replies
    1
    Views
    840

    SD and MAF, when to tune in both?

    Hi guys, I have a question, from what modifications it is necessary to tune the SD and the MAF so that the dynamic airflow and the airflow measured by the maf are very similar as recommended? I'm...
  13. Help, calibrating VE table on SD mode, limp mode

    Hi Guys, I am tuning a 06 Chevy silverado 5.3 heads / cam and started by calibrating the VE table in SD mode, to then calibrate the MAF, apparently when I get out of 100% of the board, the PCM enters...
  14. Replies
    0
    Views
    774

    Diagnosing a GM A6

    Hi guys, could someone give me an explanation to diagnose a good malfunction of an A6, and if someone has some channels or graphics for the Diagnosis?

    Thank you.
  15. Replies
    2
    Views
    915

    Coincidentally 2010 is the one I'm most in need...

    Coincidentally 2010 is the one I'm most in need of, thank you very much my friend
  16. Replies
    2
    Views
    915

    Silverado 5.3 A6 Stock Tune

    Hello guys, someone could help me with a stock tune of Silverado 5.3 A6 to make some comparisons, since it had the repository and is no longer there.

    Thanks in advance
  17. Replies
    3
    Views
    1,855

    Yes, do not complicate leaving everything like...

    Yes, do not complicate leaving everything like this and you only have to configure the PCM for 6.0 and 4L80, it is very easy with the tool segment swap, just look how it is used
  18. Instaled cam on ICL, what is there to do?

    Hi, guys.

    I have a question about when a cam is installed in its ICL, since when compared to install it in its intake centerline, the cam is moved a few degrees, thus changing its installation of...
  19. Replies
    1
    Views
    1,648

    A6 Nice tune, please help me

    Hello everyone, someone can send me a good tune of an A6 trans, someone who has gotten the maximum in performance, fast shifts, time shifts and good torque in the shifts.

    It is to build a good...
  20. Replies
    13
    Views
    12,981

    Your problem may come because the modules are not...

    Your problem may come because the modules are not receiving the brake signal, you're going to have to ing?nate them with someone who helps you install a system that recognizes the signal of the brake...
  21. Replies
    11
    Views
    14,077

    How many is the maximum retard that can be given...

    How many is the maximum retard that can be given to a stock engine?
  22. Replies
    11
    Views
    14,077

    VVT Tuning HELP

    Hello everyone.

    I want to leave some doubts about the VVT tuning.

    How many degrees of advance and retard the cam can give to find the best performance?

    How to know when to advance or retard...
  23. Replies
    4
    Views
    3,584

    I have the cut off as you have it, but I want as...

    I have the cut off as you have it, but I want as the cut off is activated, make longer pauses as a traditional 2-step or Gen 3
  24. Replies
    4
    Views
    3,584

    Gen 4 limiting as 2-step limiter?

    As I make the rev limiter a Gen IV system do as having installed a 2-step limiter?
  25. Replies
    0
    Views
    1,058

    High Octane Table, help

    Hi, may send a table main spark, which are brought to 5.3 as much performance? or you can instruct me to know how I can make a more aggressive table to try to get the best possible performance engine...
Results 1 to 25 of 40
Page 1 of 2 1 2