Search:

Type: Posts; User: Creton

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    7
    Views
    1,390

    no Mopar stuff that I can see

    no Mopar stuff that I can see
  2. Replies
    0
    Views
    322

    LS Swapped K10 HARSH Gear Engagement

    I have a K10 that was LS swapped and had wiring issues, got the issues resolved and discovered that the 700r4 was bad so I went ahead and swapped in a 4l60. After using a DD SGE-100 relay device and ...
  3. Thread: 09 ram 5.7

    by Creton
    Replies
    20
    Views
    3,378

    I posted a complete cam'd tune file with trans...

    I posted a complete cam'd tune file with trans settings for a '09 Ram. Just search my post
  4. Replies
    4
    Views
    982

    Thank you for all the help! Got it where it...

    Thank you for all the help!
    Got it where it doesn't stall out and die when coming to a stop!

    Zero'd out all the idle tables and just set it to static idle at 872rpm.


    Still working on the...
  5. Replies
    4
    Views
    982

    '71 RoadRunner 5.7 Hemi Swapped

    I have a "71 Roadrunner with a 2005 5.7 Hemi/ manual trans swapped in. over all the car runs great and has a good idle, good acceleration and overall seems to be in order with the exception of coming...
  6. Replies
    3
    Views
    1,016

    TIPN can remember up to three VIN's, however, I...

    TIPN can remember up to three VIN's, however, I have seen several that once a secondary VIN or reflash has caused the unit to loseit's stored VIN. Most dealers can reset, or if you have a LAUNCH, you...
  7. Map, throttle both showed 100% koeo

    Map, throttle both showed 100% koeo
  8. Had one so the same thing, ended up being the...

    Had one so the same thing, ended up being the crank position sensor.
  9. Thread: Wot timing e85

    by Creton
    Replies
    3
    Views
    1,403

    HC+ lean them and slow the timing down seems to...

    HC+ lean them and slow the timing down seems to work best for our area.
  10. Replies
    3
    Views
    1,016

    Sounds like the TIPN lost its VIN

    Sounds like the TIPN lost its VIN
  11. Replies
    11
    Views
    3,826

    last time I tried to purchase a quarter horse,...

    last time I tried to purchase a quarter horse, they were out.
  12. Replies
    4
    Views
    1,551

    go to Lasota racing and download it. Great book

    go to Lasota racing and download it. Great book
  13. Replies
    11
    Views
    3,826

    I scan with Linex or Snap-On , the use HP tuners...

    I scan with Linex or Snap-On , the use HP tuners to dial it in.
  14. Thread: 392 Nag1

    by Creton
    Replies
    10
    Views
    4,235

    Do a search, I posted a 392/a5 tune in the...

    Do a search, I posted a 392/a5 tune in the transmission forums. Shifts great. Give it a look.
  15. Replies
    5
    Views
    1,399

    The can/IHS Bus is not connecting through the...

    The can/IHS Bus is not connecting through the datalink. I believe that the gateway module is actually bad as it will connect if the oem harness is connected but will not connect if the smart-access...
  16. Replies
    5
    Views
    1,399

    2018 Ram Classic Can't read or connect

    I have a 2019 Ram Classic that I am planning on tuning. I have an updated VCM Scanner Suite and a new MVPI2 Pro. I found the Smart-Access behind the drivers kick panel and install the Smart-Access...
  17. Thank you for the advice. I'll post a log when...

    Thank you for the advice. I'll post a log when it comes back to the shop.
  18. 2010 C6 with Edlebrock S/C 3.25 Pulley, Headers, Full Exhaust

    Hello,

    I have been tuning Mopars for sometime now and had a customer come into the shop for some work on his 2010 C6. We changed to a 3.25 Top pulley and tuned him on the Dyno, We made 551HP/588TQ...
  19. Replies
    10
    Views
    5,990

    remove the front driveshaft. I just dyno'd a...

    remove the front driveshaft. I just dyno'd a Trackhawk and disable the Mp3023 by fuse and disconnecting the actuators, it still has residual pressure on clutches. Smoked the clutches on 3 passes....
  20. Thread: 545 basics

    by Creton
    Replies
    11
    Views
    6,737

    How are you unlocking the convertor in each gear?...

    How are you unlocking the convertor in each gear? I tried setting the RPM to 8160 which is max, but it would still engage. I changed all tables in partial to full lock to max.

    Thanks,
    Creton
  21. Replies
    9
    Views
    3,174

    Thanks, I'll try that

    Thanks, I'll try that
  22. Replies
    9
    Views
    3,174

    108758

    108758
  23. 108754 Here's one I use, works great, shifts...

    108754

    Here's one I use, works great, shifts firm but can be softened up for preference. As usual, do diligence is urged when using a different file.

    Creton
  24. Replies
    9
    Views
    3,174

    Where do you find this parameter? I'm using beta...

    Where do you find this parameter? I'm using beta version and have looked into Main version as well and don't find it?
  25. Replies
    0
    Views
    746

    Transmission P1818 code after tuning

    I had a friend who swapped his 2008 GMC 5.3 to a 6.0 retaining the 4l60. We tuned the engine to get it running and had to sort out several misfire issues as well as some wiring issues from backyard...
Results 1 to 25 of 37
Page 1 of 2 1 2