hello
has anyone played with the Torque max feature under TCC adapts (highlighted in green attached).
appreciate some insight into what this might do.
thanks
Type: Posts; User: GENFGTS
hello
has anyone played with the Torque max feature under TCC adapts (highlighted in green attached).
appreciate some insight into what this might do.
thanks
no one have any experience here?
Hey Guys
I'm trying to decipher the meaning of the
Trans Torque Management Type: Clutch Control
Clutch Torque Management Types:
SCTM?
SCTM TERM?
SITC DEC?
Some thoughts are below
not quite pushing through it i don't think.
i did see on that run timing didn't come down enough, its set at -18 will adjust back to -20
i'll add more channels like you say there.
i had upped the...
hjtrbo - good point
yes your base pressures are higher than mine.
i have the standard stall. did you up pressures before you put the stall in?
my tune attached and run file attached 1/4mile occurs...
hey guys
i'm interested in this as well. So good you have raised the topic. i have similar mods making 660rwhp
Agree with Hjtrbo that spark>torque is set at positive 5 degree. really need to...
thanks Bill
do you publish on the forum?
Hi
Does anyone know if HP tuners are having issues with their servers that would cause issues with syncing an interface.
Do they publish to the public when issues or outages occur and or when...
Hi All.
My computer crashed this week and I had to get a new hard drive.
So I?ve downloaded the latest stable version of the software 4.8.7 and MPVI2 drivers and now get a ?faulted? error message...
Hi Weston
Is there much difference/updates in
4.9.684
vs
4.9.738
thanks
Thanks Weston
keep us posted with updates..I'm following this thread.
106958
I think you PE enable is set as 15KPA, mine is 85KPA (LSA)
On the PE Tab look at Throttle 'HOT'
Your low rpm setting is saying to enable it above 43% TPS
My suggestion is to lower...
hey
the issue was in the maths..user defined..
the parameter i selected was MPVI2 Pro input analog One (initially thinking this is the wideband)
i needed to select the wide band under oxygen...
Good news! i got it sorted.
Thanks 07GTS and the other guys for your feedback as it was all helpful.:cool:
Hey guys
I wanted to just recap on the wide band setup as i think my issue may be in setup. transform
Quick recap on the steps I have done adding the wideband
add channel
Find MPVI2 pro input...
hey
i have tested the display properties using the defaults and my own colours with no luck.
test attached.
The predefined EQ error works as a test example.
This just seems to be an issue when...
Hey 07GTS
The predefined Maths AFR Error expression in red i can't seem to change.
Ive tried EQ Error also with the same result. it looks to plot but no values appear.
i basically copied the...
Hi All
I m looking for some assistance with getting my scanner to log AFR Error % using my wideband.
I have had a go and tried many variants and the output is always seems to be the same so i...
nice one LSA R8
Hey
Yes i see there now pattern B -WOT in the scanner
set at 278kph and 6500rpm should have likely shifted.
If it was me i would try lower it to 250kph and try again
your engine is...
hey
humm yes
you look to have hit the shift points: kph/rpm
TPS not quite 100%?
agree if its seeing 'hot' it would highly likely never change
Except - Hot - WOT - RPM - 6500rpm
Hi All.
Can i ask if anyone has an external weather station device that measures air density that they have linked to the VCM Scanner?
Have you been able to log data through the VCM scanner
...
Hi All,
Presently i'm looking at my Torque Management setting: specifically the Boost ramp setting. value: 0.20 (see image attached)
I would like boost to ramp up sooner than it currently is...
Hi All.
I'm looking for your assistance with identifying which would be the best channel in the VCM scanner to monitor issues with the Boost Bypass Actuator & boost solenoid.
I have tried...
I've worked it out i think