Search:

Type: Posts; User: hjtrbo

Page 1 of 7 1 2 3 4

Search: Search took 0.00 seconds.

  1. Would you mind trying this? So many things have...

    Would you mind trying this? So many things have been adjusted in your posted tune. Please perform a KOEO adapt reset / preset with the scanner after flashing. This will shift funny for a drive cycle...
  2. Would you mind giving this a try please? ...

    Would you mind giving this a try please?

    109918

    During the 5th to 6th shift the TCC is active but just doesn't have enough pressure going to it to keep it locked.
  3. Replies
    1
    Views
    52

    Log of it happening would be good. Are still...

    Log of it happening would be good.

    Are still 6L80?

    Try the following:
    Torque Management -> General -> Torque reduction -> Power downshift = Enabled
    Shift Timing -> Downshift -> Desired Shift...
  4. Replies
    2
    Views
    56

    Same as 5FDP. Mine is still stock at -20. ...

    Same as 5FDP. Mine is still stock at -20.

    109874
    109875
  5. Replies
    2
    Views
    258

    1) Unlocked at WOT, I'm no help to you there. But...

    1) Unlocked at WOT, I'm no help to you there. But I do run the max TCC pressure of 758kPa with adapts off to keep it locked solid during cruise. Anything above 50% throttle and it slips. It's not a...
  6. Thread: Ltft

    by hjtrbo
    Replies
    9
    Views
    244

    Yes. Just be aware the MPVI2 doesn't have a low...

    Yes. Just be aware the MPVI2 doesn't have a low voltage cut out so if the car isn't driven for 2 or 4 weeks you'll have a flat battery. First hand experience.
  7. Replies
    0
    Views
    110

    Excel calculator for virtual torque tables

    Hi all,

    07GTS and I have come up with a quick and dirty virtual torque table calculator. This guide is suited to vehicles where there is suspicion that the air and or fuel model is off therefore...
  8. Thread: 6L90 Tuning

    by hjtrbo
    Replies
    2
    Views
    99

    Where do you want to start lol. Post up a...

    Where do you want to start lol.

    Post up a log of what you are talking about just so we can make sure there is nothing else holding you out. Timing etc. Should pull alright on the flats in top...
  9. Replies
    15
    Views
    435

    How are you going with the shift point changes...

    How are you going with the shift point changes mentioned to you earlier by a couple of us? All sorted now?
  10. Replies
    15
    Views
    435

    My single disc high stall won't survive 1000Nm+...

    My single disc high stall won't survive 1000Nm+ though it locked. Breaks away at about 500Nm from my logs so I just leave it unlocked and only lock it in 6th at low throttle percentages. I'm not...
  11. Replies
    7
    Views
    959

    I had the same issue with my 6L90 and support...

    I had the same issue with my 6L90 and support first added the use regulator settings switch which allowed me to use the reg offset and gain. Then later on support added the desired pressure table.
    ...
  12. Replies
    9
    Views
    309

    You have made large changes to the transmission...

    You have made large changes to the transmission pressures which will now upset the adapt values that have been learned with your previous pressures. I would recommend an adapt reset / preset and...
  13. With regards to your last paragraph, and the...

    With regards to your last paragraph, and the knowledge you have gained of the FA table do you think you might be able to get it through emissions? There should be a PID Engine Off Time which will...
  14. Not sure on the details of how or why but mine...

    Not sure on the details of how or why but mine does the same e67. No dtc codes present.
  15. Replies
    4
    Views
    181

    I had a similar issue with my mystery injectors...

    I had a similar issue with my mystery injectors installed that were still using the same factory data except the flow rate which was scaled to suit the injectors. I would be +25% lean on decel before...
  16. This will get you 90% of the way there. If there...

    This will get you 90% of the way there. If there are bugs please let me know and I'll fix them.

    What you will have to do once it is downloaded is remove the .hpl extension so that it becomes a...
  17. There is a fan speed vs AC pressure table....

    There is a fan speed vs AC pressure table. Without your tune been posted can't say if it exists on your OS. If you find it, start by moving the values to the left. I use it on mine and ended up...
  18. Making Sense of (some) 6L90 (6L80) PCS and Line Pressure settings

    Expert guys know this information already, but for the newbie (me included) who is trying to understand and learn some of this stuff rather than just doing what book x or video y says, I have put...
  19. Replies
    1
    Views
    183

    All PCS channels, 20Hz Torque converter slip,...

    All PCS channels, 20Hz
    Torque converter slip, 20Hz
    TCC pressure
    Torque, 20Hz
    Torque management advance, 20Hz
    Trans slip rpm, 50Hz
    Trans current gear
    PRNDL Status
    Trans shift mode
    Time of...
  20. Replies
    4
    Views
    1,597

    Edit. Difference is I don't have my PCS max...

    Edit.
    Difference is I don't have my PCS max pressure aka Max Pressure set to 2000. Mine doesn't drag like the OPs does and I can't feel it. Noticed other PCS valves do it to.
  21. Replies
    3
    Views
    172

    Check pcs 1 is rising with load. Also connect a...

    Check pcs 1 is rising with load. Also connect a pressure gauge to the test port and verify with the service manual. On a stock transmission the pressures you see should approximate the values below...
  22. Further comments with respect to your trims, if...

    Further comments with respect to your trims, if you're 15% rich in the trims at idle, what that will do is ruin your open loop for the first 15 - 30 odd seconds (or however long your closed loop...
  23. Replies
    4
    Views
    1,597

    I know I'm replying to an old thread. Noticed...

    I know I'm replying to an old thread.

    Noticed the same thing on mine only when first starting off. To complete the thread I'm having a guess its the clutch purge function.

    FYI screen shot is...
  24. Replies
    15
    Views
    435

    1) Looking at your trans slip PID one would think...

    1) Looking at your trans slip PID one would think you're blowing through the trans on 1st gear. Do you feel the same?
    2) Very little torque management. Still got 10-12 deg of timing in on the shift...
  25. ^^^^^ ...

    ^^^^^


    https://www.aemelectronics.com/products/gauges/digital-gauges/x-series-wideband-uego-OBDII

    Works seamlessly with HP Tuners. Pops up in the scanner as a channel to log. It's awesome.
Results 1 to 25 of 175
Page 1 of 7 1 2 3 4