Hi all,
I don't know if it's possible, but wanted to ask - Is there a way to make it so DEFCO doesn't unlock the converter everytime? Trying to squeeze all the fuel economy I can out of this 6.0...
Type: Posts; User: Brettworth
Hi all,
I don't know if it's possible, but wanted to ask - Is there a way to make it so DEFCO doesn't unlock the converter everytime? Trying to squeeze all the fuel economy I can out of this 6.0...
http://www.superchevy.com/how-to/engines-drivetrain/0905chp-camshaft-lobe-separation-angle-performance-test/
This is a good read and test for LSA.
After putting long tubes on my trucks 6.2, the CL Fault is present. The ECM really doesn't like the added distance from the O2 sensors to the exhaust valve. From my understanding, you can't change or...
Thanks for the info!
I'll fail the maf correctly next time, and set it for closer to 14.6.
So I set the truck to run at 12.2, open loop, MAF unplugged, and added 15% to the entire Virtual Volumetric Efficiency table. I'd rather waste fuel than pistons.
Drove the truck around and logged...
Sweet! Thanks guys!
I need to do this to my truck, this sounds really bad, but where is the table to change in the GEN4? I've logged longterm+short term and also have a wideband. I've used them to fine tune the MAF, but...
Hello!
I am swapping in an LHU in place of my blown out LNF and since the motor is so clean, I wanted to use the LHU intake and exhaust. So my question, is the Map sensor on the LHU the same 2bar...
Yes, they are wired up correctly. Using a Tech2 I can turn them on. The Fan 1 controls are PWM for some odd reason, and fan 2 does nothing with the engine running. I can manually activate the relays...
How do I learn to perform this? This is a very powerful tool, and lots to learn.
I do.
Hello,
I have an 01 Computer, that the output controls operate both fans, and when the 6.0 is running, the Fan 2 will not operate. How do I upgrade my computer OS? Do I have to pay/use more...
Thank you very much!
5811458115
What does a channel file look like? My "Channel Configs" folder is empty.
Thanks for the help!:hi::hi:
How new is the new 3.0? I'm downloading it right now.. I had the same exact issue with Cylinder airmass - the table (when it worked was freaking amazing!) wouldn't do more than the first row on my...
Well I just looked in the repository and found a factory 4.8 tune for a 2007.56274
Do a compare and then swap over anything that is different.
I copied the VVT from a bone stock 2014 6.2 and have to say I was quite impressed with the butt-dyno and drive ability. That's always fun. I was shooting for an MPG improvement, but I barely can say...
I completely agree on the compression ratio. I really haven't tweaked anything in the high octane table, so that's one of the reasons for no "feel" or "butt-dyno" difference, as well as no MPG change.
55957
Here is the current tune I'm running.
Yes, the L9H engine recommends premium. Not once have I noticed a gain. I really just wanted to make it run the best on regular.
I'll post the tune when I get home. The scanner was originally set up to find out what my hesitation was, turns out you shouldn't go over 140K miles on the O2 sensors. ;)
I think I'm really happy with the tune at the moment, if anyone would like to give me some advise:worship: via looking at the log, that would be sweet.
This was in cold weather pulling my two...
90% sure you are right and can disable DoD with the shifter in M. I will tell you there is little to be gained with 3.08, and all of your oil consumption is caused by the active fuel system. It's not...
54813
Thanks again guys! You ROCK!