Nothing yet, but plans to do dual Walbro 450's, one boost activated, with a full return system, and 1300cc injectors. I plan to run the primary fuel pump through the FPCM, since that circuit is...
Type: Posts; User: NotSure
Nothing yet, but plans to do dual Walbro 450's, one boost activated, with a full return system, and 1300cc injectors. I plan to run the primary fuel pump through the FPCM, since that circuit is...
Have a 6.2 with 2.3L Whipple, 7 psi, and the stock flex pump was enough IF running “gas”(E10), but the whipple supplied GM 50lb injectors were over 100%. 72lb injectors fixed that. But on E85, the...
I aaume that you mean to SUBTRACT a couple of degrees here? I don?t have the timing/EGT drawing that ?doctor king? posted awhile back, but it shows the supposed increase of EGT that added timing...
I found that even when commanding 0 slip, and IF it hit 0 slip and I continued to hold dead steady load/throttle, the TCM would start ticking down the TCC pressure until it began to slip again, then...
Inertia factor profile is for shift feel. You need to make changes in the part throttle shift scheduling by vehicle speed. Take a look at the Bluecat tool
As-designed by GM. See my comment in this post about tcc regulator gain.
https://forum.hptuners.com/showthread.php?88523-Torque-converter-lock-up-6L80e-in-a-patrol
Didnt look at your log,...
I think you want around 2-4 kpa on the crankcase, which looks like your customer had at idle, but the measurement taken right at the venturi would not be accurate for the whole volume of the...
Are you filtering data to get steady state fueling conditions? For example, a filter for no accel pedal changes within +/- 500 milliseconds?
This would probably only catch oil at idle/low load (vacuum) conditions, I think you would have negligible flow through the valley connection at heavy load, through the 2.5mm orifice. But I think...
Yes.
For what it is worth, I actually did read this post and others you have made, and some have helped me better understand pcv systems. I just don't agree with all of your absolutist views. ...
Fuel dialed in means tuning the MAF and VVE. You don't want to change the injector data if they are the original injectors that came with the truck.
Dialing in the MAF means pasting the % of...
Rob, if you have a stock LS7 valley plate, it has a baffle system attached to the bottom, and the hose barb should have a 2.5mm fixed orifice inside.
I'm not clear on how you have things routed...
Ok, now I see the venturi valve on their website. I don't have that, both hoses (one from the catch can off the left valve cover, and one off of the right valve cover) terminate in the intake duct...
No pcv valve in this engine as-delivered from the General. But anyways, I thought you said that oil passing through the pcv system was good, to give everything a nice rust-resistant coating?
+1000. Bone stock soccer-mom grocery-getter before I got ahold of it and literally destroyed the pcv system. Oil dripping all over the freaking place from that manifold when it came off. But,...
I have to add, the original check valve that came with the kit seemed to take a little bit of pressure to unseat it when blowing through. This was after being installed for about 4 years. They have...
I've had their E2-X catch can setup installed since my blower install. The only thing the dual inlet can does is add a second port to the can that you connect to the intake tract pre-throttle body. ...
THANK YOU blindsquirrel! That makes sense now that I read the descriptions of the different widebands on the AEM website, the -0334 specifically calls out OBDII Can, vs AEMCan. Will the 0334 work...
I have the AEM 30-0310 Inline wideband and am trying to get it tied into the CAN on a 2013 GM truck. I've had a permanently mounted analog input Ballenger for years on this truck. I used this AEM...
Do a search for the injection timing tool (Excel spreadsheet). Adjusting injection timing might reduce smell if it is injecting into the overlap area of the stage 2.2 cam.
I have been using a Surface Pro 3 for a few years and it is perfect. Long battery life and compact. I don't use it as a tablet, I leave the keyboard/cover attached.
Is this a common problem with the AEM X series? I've had an analog input Ballenger on the left bank of my late Gen4 truck for years, had an AEM 30-0310 inline that I used with serial input when I...
I don't know what vehicle you are tuning, but my old Gen 3 truck I could put the trans in D2 and it would start out, and stay in, 2nd gear. This helped to hit higher load/low rpm areas on a launch. ...
Has anyone used these or other to trigger external outputs when certain CAN data is met? An example would be a warning light on the dash if fuel pressure drops too low, etc. Ideally it would be...
A need came up for me recently for a diagnostic scan tool (2016 GM car not supported by HPT), and am looking for suggestions. I have a tech2, but the car is too new and uses GDS2/MDMI. A friend...