Jason, i would guess your settings in the vcm editor may have been turned of by prior tuner/owners. Pull current file , run a compare file (stock one) and look at the Engie Diag. tab, DTCs, SES...
Type: Posts; User: HemiFeverAZ
Jason, i would guess your settings in the vcm editor may have been turned of by prior tuner/owners. Pull current file , run a compare file (stock one) and look at the Engie Diag. tab, DTCs, SES...
if you want some help best to post your stock file, your current modified file, and a scan if you were able to run one
ok made adjustments as you will see attached.. car runs excellent, passed Bank 2 side but not bank 1.. looking for some feedback. made big steps forward..
Scan, tune, and image attached.....
bumb
144040
Hello all from AZ! Years of Topfuel/Afuel exp. took TheTuningSchool for Dodge Hemis, so i can work on our personal 09 srt8! Good to meet an introduce!
can you post your original diablo tune, before you adjusted to review the compare changes you made.
so i pulled to tune i shared, an the one MI gave me..
Have a few questions to understand changes,
The settings in the Torque Correlation, bumped up like that makes it come in sooner or better...
Why do some adjust these settings example turn on Use ETC B when its a manual car?
@MI, thank you .. your the one out of vegas yea? Thank you for what you sent over will check it out this eve an give a whirl! Im in Vegas often will have to visit!
JohnnyFW, i did that. thank you . still didn't fix the setting monitor status. thanks for the input
Scanner Layouts, others may want to share..
work in progress so far. 143902143902
Looking to start building out our 09 SRT for the OPTIMA Street Car Challenge, who else her tunes an runs the series?
Thank you
Welcome @mikeloko i run a AFR500v2 with my kit via the Prolink. they did just come out with a new V3.. worth the tool add. USA built Ballenger Motorsports... great customer services also
143901 scanner data
Been working on this tune quite a while now, can i get fellow hemi tuners to peek and share some feedback?
Took the tuning school, an grew up working on Nitro Hemis, so hope not bad.
About the...
What changes on a nag4 09 do you recommend playin with changing to no cats? i see there are many settings in the COT area.
Long tube headers, had high flow cats, and have removed them , i have disabled the rear 02 items, what other steps do you are recommended to adjust? I do have a Wideband installed also.
Unit has...
Anyone one else>
ill run them another time to clean them up. any different recommended ways when recording them?
What do you mean about the Cats? They are magnaflows, put on last year? do you mean there bad? due...
:drivin:
I have attached the Tune, and Scan,, would like some help reviewing.. I have done a tone of self schooling, and knowledge building..
Here is about the car
2009 srt8 6.1 6 speed....
Question,
setting up my new sensor in the scanner, i have installed and setup my AFR500v2 unit to the prolink on the 1st channel, i setup that part, an working on the transform selector.
the...
anyone have some recommend steps on a LM 2009 hemi? the Training books are based more on the 15 up.. i have a 09 a little different.
I have setup from what i best can. to align with my 6.1 data.. would like to review.. i can setup a Zoom meeting right away if i get your email address.. would be great to have someone tell me if i...
im having issues with new densos causing P2096 Post Cat. Fuel trim system too lean and p0133 on both sides.. would like to know if this turning them off or work around will still pass az emissions.
fellow tuners. .looking for some feedback.. have been running car for long time no tune. an stock 02 sensors, while putting new clutch in.. an working on the suspension, had exhaust out, and...