Search:

Also esp/traction control can be deactivated under ENGINE/ GENERAL/ DISPLACEMENT. Changing the displacement to any number other then stock will turn off ESP/TC. The traction control light will always...

Yes for the trans go to Trans DTC section same thing. The thottle body if key on and unplugged will give you the red lighting bolt above the check engine light. Didn't have the plug all the way on it...

(Permanent) is just stored codes and should throw a light. Active pending do.

Fist thing open VCM Editor click on EDIT (upper left of screen) in the drop down click on VIEW, next drop down change it from BASIC to ADVANCED. To turn most stuff off it will be under ENGINE DIAG...

Yes you can. Engine Tab / General/ Engine / Displacement 3.8L.

If you hold the mouse pointer over Displacement tab a description will pop us at the bottom [ECM] 13512 Setting this value to...

I'm running a Comp 268THR13 214/233 113lsa with a phase limiter in my 5.7 and had no luck with ANN on. Truned off ANN, Dialed VE, idle rpm, increased base running airflow (feedforward control), I...

I would email support and ask. Maybe they have it listed wrong and should of been 14-19 instead of just 14. I have no experience with 3.2 vehicles.

Yes I'm thinking ground also. I cant remember we're the coils ground but belive the block. If your firewall to block or coil to block is bad it would definitely cause issue as the coils are very...

Its vehicle spacific. What year, model, engine is it you are referring to? Here is the vehicle supported list for HP Tuners.
https://www.hptuners.com/vehicles/

I used my NAG1/A580 that came in my jeep. Changed the bellhousing to the v8 and v8 converter. The CAN data has different "hand shakes" between modules varying by vehicle and year. The 2012 challanger...

Yes that should do it. If you ever want to do cams, intakes, headers, forced induction get the pro version as you can data log with a wideband O2 sensor which integrates into the scanner. Makes it...

I used a 2012 Challanger 5.7 ECU. It has the same CAN bus protocols in it as the JKU 3.6 ECU to communicate with the bcm, tipm and such. I had my vin put in it also to make the SKIM happy. I needed...

Im ure your aware Mopar Connecter will have all the pinouts for the pcm and senor connectors. I just finished a 2017 5.7 hemi into my 2013 3.6 v6 jeep wrangler rubicon. Made the swap a lot easier.

Yes you can turn off coil and injector sensors with Hp Tuners and many many more by unchecking ses/mil in the engine dtc's section in the tune. Once doing that the pcm will no longer monitor that...

Tested desired/commanded rpm on the scanner and it stays at 800rpm 2wd 4wd and 4wd lo. I am running a cam in my 5.7 it dosent like anything much under 800 for idle. The 2800 stall converter...

Your same problem I took in consideration when doing a 5.7 hemi into my 13 Jeep jku rubicon with the 4.1 low range t case. I went with a higher then stock stall torque converter. I do not have this...

From what I understand the idle is torque based (airflow and timming) to control idle rpm.. You could lower airflow and timming in the idle tables to create less torque at the same idle rpm. Being in...

Easy try might be raising the [ECM] 44216 Stopped VSS found under Engine, Idle, General. Maybe try 5mph. It should keep the idle at PN idle rpm under 5mph. Only reason I say easy try is I have only...

What is the fuction of Platform type in the tune? I did a Hemi swap on my 13 Jeep JK. The platform type comes up as LX Car. The tab definion says changing this value is not recomended. It is a LX car...

Is it possible to OS swap on 2011-14 29Bit GPEC2 PMCs . For instance swapping a 6.4 calalabration into a PCM with a 5.7 calibrabraion. Looks like both PCMs are the same Part Number f

Was trying to get an answer before spending 4 credit and possibly bricking the pcm.

Are OS swaps possible on a 29Bit GPEC2 pcm with
other OS's that share the same pcm from this list?
29Bit GPEC2 pcm
2011 - 2014 Dodge Challenger (all trims)
2011 - 2014 Dodge Charger (all trims)...

I have a 03 AWD Silverado SS running low 11's. 408 Lq9 w/LS3 heads with a F1R and to much to list. 10,000 miles on this setup.
...

Im trying to set up a high idle feature for a rock crawler with a on board welder and air ran off the engine. The engine is a 06 LQ4. Since this is a transplant motor there is not a BCM which I...

I had the Beta 2.0 for Ford but lost it when my Laptop crashed. I had a ford tune saved on a flash drive and cannot access them with the latest version.