Search:

Type: Posts; User: 68Camaro

Page 1 of 14 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    481

    Injection timing

    anybody know if the Dodge platform has a table to adjust injector timing like the GM platform has?
  2. 2011 ford f150 5.0 cams zero out after shift.....

    after shift cams zero out for about 1 second before moving back to optimum power with about 60ft/lb torque loss....

    have made several changes but haven't found solution...

    hoping someone can...
  3. 2011 ford f150 5.0 cams zero out after shift.....

    after shift is completed cams zero out for about 1 second..... about 60ft/lb torque loss until cams move back to optimum power settings

    have made several adjustments to attempt to prevent this...
  4. Hello Bill I purchased an MPVI3 and emailed...

    Hello Bill

    I purchased an MPVI3 and emailed support - they are telling me I have to send in my MPVI2 interfaces to have the licenses transferred over to the MPVI3.....
    this makes no sense to me...
  5. Replies
    2
    Views
    1,037

    thanks for the response!! greatly appreciated...

    thanks for the response!! greatly appreciated sir!!
  6. Replies
    37
    Views
    4,310

    this is a problem with P01 and P59 ECU's because...

    this is a problem with P01 and P59 ECU's because there is no built in baro correction in SD - these ECU's do fine with altitude changes as long as you keep the MAF which is not possible in a big...
  7. Replies
    7
    Views
    1,461

    long term fuel trims always can be carried into...

    long term fuel trims always can be carried into WOT during transition - I always disable LTFT's in my tuning to prevent this issue
    fuel>oxygen sensors>ltft enabled - set to disabled and set minimum...
  8. Replies
    9
    Views
    2,935

    I fixed it....

    I fixed it....
  9. Replies
    9
    Views
    2,935

    I know this thread is 5yrs old - was there ever a...

    I know this thread is 5yrs old - was there ever a solution found for this? I have one doing exactly this same thing......
  10. Replies
    0
    Views
    719

    6l80 goes into 5th gear and stays there

    I tuned a DI 5.3 swapped C10 awhile back with a 6l80 trans - everything went smooth no issues - now a few months later truck is back. Trans goes straight into 5th gear and stays there - I haven't...
  11. Replies
    6
    Views
    1,487

    Thank you Sultan - that fixed it :)

    Thank you Sultan - that fixed it :)
  12. Replies
    6
    Views
    1,487

    problem happens at part throttle and only 80kpa...

    problem happens at part throttle and only 80kpa
    Car hasn't made over 155kpa at WOT on the dyno - thanks for looking though

    I have a ticket in with HPTuners support..... pretty sure the beta...
  13. Replies
    6
    Views
    1,487

    2015 Dodge Challenger 3000rpm limit

    5.7 hemi with procharger keeps hitting 3000 rpm limit - I have all the rev limiters I can find raised

    says to service anti-lock brakes also when it hits the limit - anybody seen this before?
    ...
  14. Replies
    2
    Views
    1,037

    2016 Charger turbo 3.6 LV2 torque monitor

    I keep getting this LV2 torque monitor error/limit - anybody seen this before? solutions?

    its been so long since I posted on this forum I can't even figure out how to attach tune or log file...
  15. Replies
    1
    Views
    952

    E92 ecu tunerlock

    are we able to tunerlock these ECU's ?
  16. Replies
    148
    Views
    131,962

    the link doesn't work using my laptop.... how...

    the link doesn't work using my laptop....

    how much RWHP are you guys seeing stock vs tuned..... ?

    thanks for feedback

    JP
  17. Replies
    11
    Views
    3,826

    99-04 Mustang tuning

    so anybody having any luck with this yet ? or does the scanner still lock up and basically renders tuning with this platform useless?
  18. Replies
    2
    Views
    1,423

    2003 cummins swap vehicle skim disable

    I have searched for a solution and haven't found and answer except that HPTuners is not able to accomplish this.....

    Hoping there is a solution now?!?
  19. Replies
    40
    Views
    21,167

    Thank you - I will give that a try

    Thank you - I will give that a try
  20. Replies
    40
    Views
    21,167

    bump I'm working with this now and am having...

    bump

    I'm working with this now and am having trouble building a histogram to log ETC error accurately - any of you smart guys have any insight or are there some more detailed threads on this...
  21. Replies
    1
    Views
    741

    where are you located? I tune this platform but...

    where are you located? I tune this platform but I don't remote tune.... I prefer to put this on the dyno and tune....
  22. Replies
    1
    Views
    2,252

    C3 pin 4

    C3 pin 4
  23. Replies
    18
    Views
    5,240

    cool - this was my original intent when I started...

    cool - this was my original intent when I started this thread.... never wanted anything for free - I do this for a living and understand paying someone for their time (and hopefully I can learn...
  24. Replies
    18
    Views
    5,240

    Thanks RickClarke23 - I appreciate your response...

    Thanks RickClarke23 - I appreciate your response and hope to learn from you and some of the other guys on here in the future.... I will keep checking back on this platform and hopefully be able...
  25. Replies
    18
    Views
    5,240

    Thanks for the response Kaleph - I just needed...

    Thanks for the response Kaleph - I just needed to rant a little and eat a snickers - I will keep digging on this platform (unfortunatly this one is tuned and gone now)

    I love cars and tuning in...
Results 1 to 25 of 327
Page 1 of 14 1 2 3 4