Search:

Type: Posts; User: JaegerWrenching

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    133

    They are fault codes and they each do different...

    They are fault codes and they each do different things. One can trigger reduced engine power and one might trigger reduce engine power, but only reduce the power by X amount instead of X amount. If...
  2. Replies
    17
    Views
    812

    Mine is doing something very similar. It also...

    Mine is doing something very similar. It also started after the update. Fails first flash on my 2018 f-250 then i retry and it works, It'll fail every time almost on certain USB ports but one is...
  3. Replies
    16
    Views
    3,014

    Can you Post your tune so i can look at it and...

    Can you Post your tune so i can look at it and see if there's a issue? It might be that you increased it outside of the parameter limits which creates the problem.
  4. Replies
    16
    Views
    418

    This is the best piece of advice for timing. I...

    This is the best piece of advice for timing. I have tried used timing calculators and values that big tuners use on a stock truck and swear by with absolutely awful results, there's just too many...
  5. :cheers:

    :cheers:
  6. Holy wow wow wow, I'm not a dodge guy but that...

    Holy wow wow wow, I'm not a dodge guy but that looks like pretty poor fueling control. It's almost setup like a light switch for fueling, on or off no in-between lol. I'd love to see a stock file,...
  7. Replies
    2
    Views
    160

    Create a ticket with support.

    Create a ticket with support.
  8. That doesn't sound like it's a proper delete...

    That doesn't sound like it's a proper delete tune, did you do it yourself? Do you have any post injection events actually happening while this message is being displayed?
  9. Replies
    1
    Views
    108

    92373 These tables will need adjusting. Do you...

    92373 These tables will need adjusting. Do you have a data log of this happening by chance?
  10. Replies
    8
    Views
    661

    I'm having the same issue with it failing mid...

    I'm having the same issue with it failing mid flash consistently saying timed out. But mine was tune related, or so i had thought. Some tunes were fine and others weren't, i had tunes i knew i...
  11. Are they elevation based tables?

    Are they elevation based tables?
  12. I'm not a cummins guy but it appears to be doing...

    I'm not a cummins guy but it appears to be doing exactly as it's commanded to do IMO. Look at your ECM 7411 table. It's following that table perfectly. Your truck goes up to 19* when part throttle...
  13. Replies
    16
    Views
    3,014

    Did you change anything related to the tire size...

    Did you change anything related to the tire size or try re-calibrating the speedometer?
  14. Replies
    2
    Views
    116

    How did you lower the MPH? The table is in OSS,...

    How did you lower the MPH? The table is in OSS, Thus you'd want to raise the OSS for it to downshift sooner not lower it. And depending on tire size and rear gear ratio that will change the actual...
  15. Replies
    3
    Views
    327

    ECM EZ Lynk doesn't have anything defined for the...

    ECM EZ Lynk doesn't have anything defined for the TCM
  16. Replies
    3
    Views
    327

    Can we get this table defined?

    I'm inserting a pic of a table I've seen in Ez Lynk and was wondering if we can get this on HPT. 2017-2019 6.7 diesel ECU. :burnout: 91929
  17. Replies
    5
    Views
    295

    Can you post a trans file for a 8l90 so i can...

    Can you post a trans file for a 8l90 so i can look at it?
  18. Post your stock file and ill look at it and help...

    Post your stock file and ill look at it and help you out. I want to see what it looks like compared to this tune.
  19. You're confused on your boost tables. High alt is...

    You're confused on your boost tables. High alt is for high altitude, you will see less boost when compared to low alt. Same goes for your torque calculation tables under torque model. They are...
  20. From what i've heard I think the way HPT does it...

    From what i've heard I think the way HPT does it is different than say EZ lynk, i think they limit the fuel timing table to certain areas based on where your switch is set. So it still works for...
  21. HP won't be able to do this without user defined...

    HP won't be able to do this without user defined parameters. So You'll need a delete tune "your best and easiest bet" or know where and how to turn off these codes in the binary file.
  22. Heck yeah always nice to see the impossible done...

    Heck yeah always nice to see the impossible done haha! Thanks for sharing and furthering the progression.
  23. Replies
    1
    Views
    347

    There's lots of good info on here, especially for...

    There's lots of good info on here, especially for GM/dodge stuff IMO. Ford unfortunately not so much. Look through old posts and take your time. But also play with your truck, it's the best way to...
  24. Nice, did you achieve that using HPT? Also what...

    Nice, did you achieve that using HPT? Also what logging software is that?
  25. Post your tune so we can look at it and see...

    Post your tune so we can look at it and see what's wrong.
Results 1 to 25 of 84
Page 1 of 4 1 2 3 4