Lambda for CNG is 17.2 : 1 (and supposedly this wideband can be used for that...) I'll see what MFG specs are. Never though of taking a butane lighter to it...
Type: Posts; User: Ace25
Lambda for CNG is 17.2 : 1 (and supposedly this wideband can be used for that...) I'll see what MFG specs are. Never though of taking a butane lighter to it...
I have a K&N air intake that has a little "shield" but it's a far cry from a true Cold Air Intake. I just built some shields to prevent the cone from sucking warm air by the headers... I'll scan...
I know the LC1 has had some issues form what I have seen on these forms, but sometimes it performs as expected??? Do you recommend a different one? Also, shouldn't my "Commanded AFR" be very...
Thanks for the response; I have been reading / learning & then reading many more threads; this is a great board with lots of opinions & lots of expert advise...
@ Russ, if you look at the scan,...
forgot to reset FT's :P oops. I remembered to do that this morning & I do have the OL AFR table set; I posted over here at the end:...
This is a very good thread! To me it seems like "lean tuning" can only be done in Open Loop... I added a few degrees of timing, originally commanded 16.5 AFR & added a few degrees of timing; -...
I'm experimenting with MPG here & have read many other posts; My Question is: when my tune is commanding Open Loop, (IE, closed loop is enabled at 284 F)
Why do I have a LTFT that varies ???? ...
On this tune, I had this car at the drag strip and saw a max of 1.5 KR; it's a daily driver & I recently did a MAF tune on it; I'm really surprised to see some KR in the Low RPM band.
I scanned...
This is like learning how to ride a bike; Thanks for being a mentor Russ! :) Before tuning, my LTFT would lock at -2.3 at WOT; now they lock at 0.0 (regular driving seems to have much better LTFT...
So, with the newer open loop table that we have, there is no need to tune the lower half of the MAF frequency & the upper half separately? I'm assuming that with the OL table commanding 14.7, that...
I was initially confused by this... To clarify, I think I should leave the PE at 14.7 for doing the first part of the tune, under 4,000 RPM & under 50% TPS for the lower MAF cells; then when I...
I have an LC1 permanently installed, so I'm assuming I can go to the "Open & Closed Loop" tab & set the coolant temp to 284F (so that closed loop doesn't enable)
I have my PE - Fuel Base vs. ECT...
Isaak, this might be a bit late, but it looks like you need to add the MAF freq error to the primary table in the VCM scanner.
- Open the scanner with the default imperial config
- Displays -...
I know this is an old thread, but this is exactly the info I was looking for; Now I can give Russ's method of MAF tuning a try: ...
My transmission started a deep creaking sound only in reverse after getting done with the major mods (had engine cradle out, new xp cam, headers, intercooler etc)
Now in reverse only it Growls,...
I just saw this
Over here: http://www.hptuners.com/forum/showthread.php?t=6045&highlight=v6+MAF
Maybe it's not a good idea to touch the stock VE table?
Overboost101, what did you find out / wind up doing?
I was told that this can't be done with HPT ??? over here: http://www.hptuners.com/forum/showthread.php?p=313463#post313463
I just removed my wideband and placed the factory O2 back in the rear... I was apparently mistaken that HPT could take care of it... On a side note, maybe I should contact them and engineer an...
Thanks for the reply. I will temporarily remove my wideband and put the stock O2 back in the rear.
The question is, will this actually help matters? being I have no CAT the rear O2 is probably...
help please :D do I need to bake some brownies and send on to y'all ??
has anyone tried creating a shortcut on the desktop, right click / properties and go to compatibility mode, try setting the compatibility mode to like windows XP
Vehicle: 2005 Monte SS 3.8 L67 with M90 blower; mods: stage 2 intercooler, xp hot cam, headers, catless downpipe, cat back exhaust, 3.0 pully, 42.5 injectors, cai...
I have an LC-1 wideband in...
I just read a really good thread about VE tuning here: http://www.hptuners.com/forum/showthread.php?t=15778&highlight=v6+tuning
To me it seems like the consensus is to do VE tuning, on some...
Different state have different regulations on how they label gas. Some states need to have a sticker on the pump if it contains 1% or more of Ethonal; other states don't have to label the pump... ...
If you don't have a cat or aren't worried about it, you could try this:
Engine error codes unchecked SES enable and set to no error reported:
P036 HO2S Heater Control Circuit Bank 1 Sensor 2...