Search:

Type: Posts; User: 1bad68ls

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. FAILED Bluetooth Connection - Track Addict &/or TDN

    I have the MPVI2+. I also have an Android (Samsung S22 Ultra) phone. I have downloaded the latest versions of TDN and Track Addict. I followed the first time setup on both applications, however I...
  2. MPVI2+ Bluetooth Pairs but does not Connect with Windows 11

    I am using Windows 11. I paired the MPVI2+ to my laptop and during the pair process, it initially showed "Connected" but then immediately changed to "Paired".

    [HP Tuners MPVI2+] shows up in my...
  3. Greg/all, I used the GenIV EOIT Excel sheet to...

    Greg/all,

    I used the GenIV EOIT Excel sheet to review my camshaft and potentially update the Boundary and Normal ECT/RPM injection timing tables. I am looking for feedback on how best to...
  4. Thanks GHuggins! I 100% agree I want the...

    Thanks GHuggins!
    I 100% agree I want the trims to be at 0. This is exactly my goal.
    I was playing with the OL tables with my cold starts. My concern with changing these tables is they are the...
  5. Thanks Alvin, I completely agree with all your...

    Thanks Alvin, I completely agree with all your feedback! I am aware of the [ECM] 12441 table, however this controls the "Commanded" fuel. I expect the production SW would have to have some temp...
  6. LSA Tuning - Running Open Loop Lean at Cold Starts

    I am tuning my VVE tables on my LSA engine using a Wideband O2 sensor. The engine is running open loop fueling only.

    When the engine is cold and I am at idle , I notice my EQ_Ratio_Error is...
  7. R Horn - Solved! I added a 100 ohm resistor...

    R Horn - Solved! I added a 100 ohm resistor between the CAN hi & lo and and I now get a lambda reading.
    Thank you for solving this issue!

    Dr. Mike, Thanks for your help too!

    Jeff
  8. Thanks Dr. Mike, I added that channel ...

    Thanks Dr. Mike,

    I added that channel [X-Series UEGO (30-03xx) WB EQ Ratio 1] but you can see in the attached screen shot, the cell is empty.
    I also included the analog WB signal thru the [MPVI2...
  9. Does MPVI2+ Support Reading AEM 30-0310 thru CAN with ProLink cable?

    I purchased the MPVI2+ with the ProLink cable and connected the CAN +/- directly to my AEM 30-0310 Wideband CAN +/-.
    I fired up VCM Scanner, connected to vehicle, repolled for parameters, and I do...
  10. After reviewing a few other tunes and the [Engine...

    After reviewing a few other tunes and the [Engine Diag] area, in the [Airflow] tab, others have:
    1) Set the min ECT to outside the operating range in the [P0101, P0106, P0121] section.
    2)...
  11. Replies
    6
    Views
    1,932

    Considering that you are running an automatic, I...

    Considering that you are running an automatic, I don't think it is wheelspin, otherwise you would see it on the VSS trace.

    I have 2 possibilities:
    1) During launch (especially up against a...
  12. RobZL1, You are right on the money! I had two...

    RobZL1,
    You are right on the money! I had two codes that popped:
    - P0106 - Manifold Absolute Pressure/BARO Sensor Range/Performance
    - P1101 - Mass Airflow Sensor Out Of Self Test Range

    It...
  13. Guys, Thank for the help! I replaced the ethanol...

    Guys, Thank for the help! I replaced the ethanol sensor. The new sensor works well and shows 10% ethanol (which is what I expect for pump gas).
  14. Hi RobZL1, Thank you for the great input. I...

    Hi RobZL1,
    Thank you for the great input. I will take a closer look at the codes and see if they were set during the trip.... which may be the root cause of the MAP clipping.

    Regarding the VVE...
  15. LSA Boost Pressure gets Clipped After a Period of Time in Same Trip

    Thanks JSLLC,
    I agree with your comments about TQ down low. I am driving the SC 30% faster than stock with the BTR stage 3 (aggressive lift) cam and I expect the torque would significantly increase...
  16. LSA Boost Pressure gets Clipped After a Period of Time in Same Trip.

    I have a ZL1 engine (Manual trans) with BTR stage 3 cam, 30% overdrive on the SC pulleys, ID1050x injectors, minor porting and headers in a 2nd gen Camaro. I tuned the MAF and VVE tables and I have...
  17. LSandlteditor, thanks for the help! The...

    LSandlteditor, thanks for the help!

    The sensor out goes to pin 5 in the blue connector. I am positive it is connected properly because when I have the Key On Engine Off, the scanner shows the...
  18. Thanks for the feedback! The default frequency...

    Thanks for the feedback! The default frequency is set to 65Hz (15% ethanol). If the sensor was not reading properly and went into default mode, I would expect it would be set to the 65Hz.... but it...
  19. Flex Fuel Sensor reading 179Hz _ Fuel Contamination?

    Hi Guys,
    I am looking for help with a flex fuel sensor issue. I enabled [flex fuel] and my flex [fuel sensor] in my E67 controller for my LSA engine for the first time. The car has 92 octane...
  20. I figured out how to fix the issue on my E67...

    I figured out how to fix the issue on my E67 controller.... in the SPEEDO section under [Calibration] tab, I changed the [Vehicle Speed Output] from [Serial] to [RepTOS]. The speedo no longer drops...
  21. I set the speed limiter ENABLE to 7000, which...

    I set the speed limiter ENABLE to 7000, which basically means that I am completely disabling the speed limiter (which is what I intended to do).

    I figured out how to fix the issue.... in the...
  22. I left speed limiter 2 alone. It is set at...

    I left speed limiter 2 alone. It is set at 217mph (see attached).103311
  23. Turned off speed limiter & it still cuts out at 100mph???

    Hey Guys,
    I am looking for help with my speedo dropping out at 100mph. I have an E67 with LSA in a 2nd Gen Camaro. The E67 and FSCM are the only GM controllers in the car.

    I have read a few...
  24. I did this in my E67 controller (see attached...

    I did this in my E67 controller (see attached screen shot). I set SOURCE: [Calibration], and Speed Limiter Comms Fail: [194] mph. The speedo still drops at 100 mph in the Scanner tool and on my...
  25. This issue was resolved by downloading the latest...

    This issue was resolved by downloading the latest software (version 4.6.3). The functions [re-poll for parameters] or [Controls & Special Functions] did not work for me in Version 4.4.4, which also...
Results 1 to 25 of 36
Page 1 of 2 1 2