Search:

Type: Posts; User: Natejk99

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    633

    Flex segment swap 1279405

    looking for a flex fuel file for segment swap 1279405 non in the repositry unfortunately
  2. Replies
    32
    Views
    11,525

    Yea makes no sense

    Yea makes no sense
  3. Replies
    32
    Views
    11,525

    Ok flashed in a very old tune from when I first...

    Ok flashed in a very old tune from when I first got it running back to the fire no start having to Hossa the gas to get it to fail the maf or something but I'm able to control fueling now shit makes...
  4. Replies
    32
    Views
    11,525

    Yea it should've stayed the same it's set to...

    Yea it should've stayed the same it's set to 78lbhr
  5. Replies
    32
    Views
    11,525

    I don't have any o2s in it . I just tuned it in...

    I don't have any o2s in it . I just tuned it in open loop the first time using my wideband, and yea the fuel pressures holding the pump is brand new magna fuel 750. I flashed in a stock ve table made...
  6. Replies
    32
    Views
    11,525

    It's doing the same thing as that tune only thing...

    It's doing the same thing as that tune only thing I changed was the little bit of injector data. Are there any ses codes that could be turned off that was cause these issues I can set the VE table to...
  7. Replies
    32
    Views
    11,525

    Ok done and done still has the same issues do you...

    Ok done and done still has the same issues do you think it could be a valve adjustment issue this all started happening after I swapped my rockers over to shaft mounts
  8. Replies
    32
    Views
    11,525

    Or copy the zero kpa table over the whole table?

    Or copy the zero kpa table over the whole table?
  9. Replies
    32
    Views
    11,525

    Thanks for the reply I made the change to the spa...

    Thanks for the reply I made the change to the spa what should I do for offset set it to 1?
  10. Replies
    32
    Views
    11,525

    Ok digging this back up having the same issues. I...

    Ok digging this back up having the same issues. I have read flowed injectors, fresh magnafuel 750, and added an iat sensor. I am still unable to make fueling adjustments I've even tried to set the...
  11. Replies
    32
    Views
    11,525

    I tried putting the bias to 2 no change gonna...

    I tried putting the bias to 2 no change gonna grab a sensor and try that
  12. Replies
    32
    Views
    11,525

    Idk how I skipped that step I did alot of reading...

    Idk how I skipped that step I did alot of reading on that subject and found some really good Info I'll try it here shortly and keep you guys posted
  13. Replies
    32
    Views
    11,525

    That was my assumption that changing rockers I...

    That was my assumption that changing rockers I should just have minimal fuel changes I'll try the iat it was like that before though.
  14. Replies
    32
    Views
    11,525

    log file

    log file
  15. Replies
    32
    Views
    11,525

    Commanded afr is 9.87 or 1.000 at all times,...

    Commanded afr is 9.87 or 1.000 at all times, until in pe and it commands .8 lambda to be safe, is there anything else that controls fueling other than the VE table that I'm missing? I didn't have...
  16. Replies
    32
    Views
    11,525

    Yes I am using a wide band set up using lambda...

    Yes I am using a wide band set up using lambda error % and I am using e85 it's probably all out of wack all the different changes I've tried to make to it I had idle areas down to 15-20 and it was...
  17. Replies
    32
    Views
    11,525

    im using a vacuum ref regulator so fow rate is...

    im using a vacuum ref regulator so fow rate is steady 78lb/hr at 43.5psi set with ref line un hooked
  18. Replies
    32
    Views
    11,525

    tune file

    tune file
  19. Replies
    32
    Views
    11,525

    I'll post the tune shortly

    I'll post the tune shortly
  20. Replies
    32
    Views
    11,525

    VE not responding to changes

    Trying to tune my ve table and it will not respond to any changes I make, its running really rich under part throttle and goes lean immediately after part throttle. I've tried everything I can think...
  21. Replies
    31
    Views
    12,326

    I haven't tried yet on mine I've been having a...

    I haven't tried yet on mine I've been having a valve train issue but my pcm is
    Serv. No. 12602801 with Hwd. No. 12589161
  22. Replies
    31
    Views
    12,326

    Hmm I'll give it a shot

    Hmm I'll give it a shot
  23. Replies
    31
    Views
    12,326

    Yep MAF fail is at 0

    Yep MAF fail is at 0
  24. Replies
    31
    Views
    12,326

    That's how mine is set up right now miles on...

    That's how mine is set up right now miles on first error idk what my maf fail is though I think it's zero I know I needed those codes to go into SD mode though
  25. Replies
    31
    Views
    12,326

    I think mine is different because it only does it...

    I think mine is different because it only does it right after i flash the computer. Any other time I start it its fine only when i gladh it is when I have issues with starting like secuirity or pcm...
Results 1 to 25 of 27
Page 1 of 2 1 2