Search:

Type: Posts; User: lukearmstrong1990

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. add it here. go advanced reply and attach file

    add it here.

    go advanced reply and attach file
  2. Replies
    25
    Views
    838

    that is not a stock file. injector settings...

    that is not a stock file.

    injector settings alone give that away
  3. What did you find and what fixed it?

    What did you find and what fixed it?
  4. Not sure with HP on cruiser but I have before...

    Not sure with HP on cruiser but I have before with ford and GM in this event just repeatedly tried write entire, disconnected battery power for 10 mins and again repeatedly tried write entire unit...
  5. Can u K Tag the stock cal over the top mate?

    Can u K Tag the stock cal over the top mate?
  6. Replies
    3
    Views
    136

    Double stoich, halve AFR terms an set the...

    Double stoich, halve AFR terms an set the injector flow rate as required.

    If dead head system, take stock table and multiply by 2% until the last cell is as close to max without over shooting it...
  7. set minimum spark to 0 not 15. 0 catalyst...

    set minimum spark to 0 not 15.

    0 catalyst heating multiplier

    edit ECT spark correction for cold idle. note the multiplier of 2

    0 out both stall saver tables
  8. Replies
    8
    Views
    637

    anyone??

    anyone??
  9. Replies
    2
    Views
    163

    file looks nearly stock

    file looks nearly stock
  10. I believe joining the 2 canbus circuits at the ...

    I believe joining the 2 canbus circuits at the trans plug and bridging the N start wire will allow you to select manual and just turn off the MIL for the codes.

    however with no speed input you'll...
  11. just turn the MIL off for those codes

    just turn the MIL off for those codes
  12. Replies
    5
    Views
    931

    make your underboost threshholds 20psi and your...

    make your underboost threshholds 20psi and your overboost thresholds 0psi.

    max out P1227 threshold and timer in engine diagnostics>airflow
  13. timing isn't really relative to displacement. Its...

    timing isn't really relative to displacement. Its relative to cylinder pressure.

    cylinder pressure is dictated by so many things. air flow in and out, air temp, compression ratio, camshaft design,...
  14. Replies
    8
    Views
    1,446

    open loop boost control

    open loop boost control
  15. Replies
    3
    Views
    1,433

    over boost thresholds will set an over boost...

    over boost thresholds will set an over boost condition when error is LESS than in the box.

    set it to 0 and max the P1227 threshold and timer
  16. looks like overboost cut also your wastegate...

    looks like overboost cut

    also your wastegate DC after 4000rpm is 0%
  17. Replies
    3
    Views
    310

    would suspect it now has a boost leak

    would suspect it now has a boost leak
  18. you can scale any map sensor and itll work as it...

    you can scale any map sensor and itll work as it should. 312.50 and -11.25 are factory LSA sensor settings and will work.

    if you plug in a MAF with custom OS it does really odd things.

    best to...
  19. Replies
    4
    Views
    559

    change inferred movement to 7000rpm enable vss...

    change inferred movement to 7000rpm
    enable vss out via SCP
    diable vss out via PCM
    VSS source 44

    try adding idle rpm with start up adder and max the time
  20. Replies
    1
    Views
    334

    943519435294353943519435294353 not the OS...

    943519435294353943519435294353

    not the OS you're after but still stock BF ZF files
  21. Replies
    8
    Views
    244

    E38 LS2 can be either E40 or E38 though. ...

    E38

    LS2 can be either E40 or E38 though.

    E38 uses 4x cam gear, E40 used half moon. Both have same reluctor
  22. your file has 2 Bar SD Custom OS applied. it...

    your file has 2 Bar SD Custom OS applied.

    it will require the MAF wires unplugged and the IAT wires left, or an alternate IAT sensor and patch harness.

    you have actual VE tables to edit and the...
  23. at 11.7:1 comp on the best available pump gas I...

    at 11.7:1 comp on the best available pump gas I would personal be around the 20-22 degree region.

    I would be cautious of knock in the transition through the mid area of the spark table as at that...
  24. how old is your software? have you tried...

    how old is your software?

    have you tried maxing the ETC rate limit in engine torque managment
  25. at least you gave him the opportunity to fix it....

    at least you gave him the opportunity to fix it. Sometimes people make mistakes, and sometimes a second opportunity with the car is needed. Quite often I've seen tuners bagged out by customers or...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4