Search:

Type: Posts; User: 1FasImp

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    1,975

    Never mind. I contacted the vendor i bought the...

    Never mind. I contacted the vendor i bought the kit from and got my answer. So i just want to say thank you for all the advise. It helped me out tremendously.
  2. Replies
    1
    Views
    1,975

    3800 Pcm swap question

    I have a turbocharged 01 impala with the 3.8 and many mods ( I believe list of mods are in signature below). I have a extra pcm from an 00 grand prix gtp and was wondering if i could use it. My pcm...
  3. Replies
    33
    Views
    12,363

    After adding and subtracting anywhere from 0.50 -...

    After adding and subtracting anywhere from 0.50 - 0.01 g/s manually from the maf curve in open loop ( seeing my commanded afr changes while driving even though its set at 14,7 adders and the...
  4. Replies
    33
    Views
    12,363

    Just for S**ts & Giggles i took the original tune...

    Just for S**ts & Giggles i took the original tune and just bumped the operating temp RPMs up to 950, and wrote it to the ECU. She fired up, but was idling @ 16.5 AFR. That was intriguing.
  5. Replies
    33
    Views
    12,363

    Yes i did that, and the problems still exists.

    Yes i did that, and the problems still exists.
  6. Replies
    33
    Views
    12,363

    I followed Idle Rinkrats Tuning guide to get my...

    I followed Idle Rinkrats Tuning guide to get my car to start and adjusted the maf airflow in the idle areas. I am currently working on the Open Loop tuning using Russ k write up. And im running into...
  7. Replies
    33
    Views
    12,363

    I couldn't figure it out. Even After reading...

    I couldn't figure it out. Even After reading through multiple threads on a few sites. Its leaving me with more questions then answers. So I decided, Im going to start fresh. I made the following...
  8. Replies
    33
    Views
    12,363

    for some reason when i start my car the scanner...

    for some reason when i start my car the scanner will read its got 14-15 degrees of knock while idling and is readiing -5 degrees in timing. And when i blip the throttle wit goes away, and everything...
  9. Replies
    33
    Views
    12,363

    Got it, Thanks. Sorry took so long to...

    Got it, Thanks.

    Sorry took so long to respond. Engine was leaking oil and coolant. Had to track that down and fix it.
  10. Replies
    33
    Views
    12,363

    Cool thanks for the clarification. Ill zero out...

    Cool thanks for the clarification. Ill zero out that table. Right now ive just been sitting in my driveway idle tuning in open loop. So far I got my WB fluctuating between the High 13s, & 14s,...
  11. Replies
    33
    Views
    12,363

    So same as before, just play with maf curve till...

    So same as before, just play with maf curve till AFR is 14.7 or within 5%. Ive researched alot on the lucas 42.5 injectors. Its really a toss up. I didnt mess with my IFR though, it was already set...
  12. Replies
    33
    Views
    12,363

    I did as said. And added to the maf. Now my Ltft...

    I did as said. And added to the maf. Now my Ltft is reading 0 in idle. my wb err is all over the place but my afr on my gauge is and in Hp tuners are reading the same thing 14 - 16 afr at idle. Tune...
  13. Replies
    33
    Views
    12,363

    Awesome. Ill do that. I was reseting fuel trims...

    Awesome. Ill do that. I was reseting fuel trims but not disabling the fuel trim learn. What about any afr tables, would i need to change any of them?
  14. Replies
    33
    Views
    12,363

    I believe the afr error is correct. I idont know...

    I believe the afr error is correct. I idont know if i typed the experssion formula in correctly or not. To shut off full trims you mean by resetting them? Closed loop wasnt enabled, to do that do i...
  15. Replies
    33
    Views
    12,363

    I did some maf adjusting to the tune with the log...

    I did some maf adjusting to the tune with the log in my last post. I also did a log after writing the changes to the pcm. Any insight would be greatly appreciated. I attached the tune with the maf...
  16. Replies
    33
    Views
    12,363

    After more researching and using lot of different...

    After more researching and using lot of different word play in google, I came across a thread for the AEM WB ( 30-0300) EGR Formula for the standard interface on an l67.
    ...
  17. Replies
    33
    Views
    12,363

    I am still trying to get this math equation...

    I am still trying to get this math equation correct for the egr to jive with WB. I took a vid with the wb and scanner while logging for an idle tune, so I could pause the video and see how much it...
  18. Replies
    33
    Views
    12,363

    Any equation need like with the egr? Edit...

    Any equation need like with the egr?


    Edit ****

    I found this video tutorial
    https://youtu.be/Ru_2M2uGSKs
  19. Replies
    33
    Views
    12,363

    Is there a write up on it?

    Is there a write up on it?
  20. Replies
    33
    Views
    12,363

    The video above works on the 3800. I was able to...

    The video above works on the 3800. I was able to get my AEM uego 30-0300 wb to log in vcm scanner through the Egr signal wire. I just have to play with a number in the equation to get it to read...
  21. Replies
    33
    Views
    12,363

    I found a how to on youtube for the wb and erg...

    I found a how to on youtube for the wb and erg for a 5.3 Silverado.
    https://youtu.be/NDyiq3A5MIc

    Would this work on the 3800 pcm?
  22. Replies
    33
    Views
    12,363

    After adding 1 gram to the maf curve in the 1500...

    After adding 1 gram to the maf curve in the 1500 - 3875hz section, 2 degrees of timing through the 0.08 - 0.28 grams and 400 - 1,200 rpm range in the hi octane table, the car is now able to start and...
  23. Replies
    33
    Views
    12,363

    I will give a try. Thanks

    I will give a try. Thanks
  24. Replies
    33
    Views
    12,363

    I set the idle to 950rpm. To adjust the maf curve...

    I set the idle to 950rpm. To adjust the maf curve i would goto maf calibration - Airflow vs. FREQ ? And to adjust the timing i goto Spark, Advanced and then Base Low Octane ?
  25. Replies
    33
    Views
    12,363

    Need advice for 3800 series 2 turbo

    Ive been researching and reading up on hp tuners for about a year now. Even when i didnt own hp tuners, i downloaded the software and some 3800 tunes, to look at while reading and watching videos....
Results 1 to 25 of 27
Page 1 of 2 1 2