Search:

Type: Posts; User: phuz

Page 1 of 7 1 2 3 4

Search: Search took 0.00 seconds.

  1. I was looking into this, too because I wanted to...

    I was looking into this, too because I wanted to use it to test things like 60' and 1/8 mile. I thought I could log the "Distance Since Last Cleared" PID, but it only seems to update from the PCM...
  2. Replies
    144
    Views
    9,895

    Thanks Greg. I completely agree and I found the...

    Thanks Greg.
    I completely agree and I found the primary issue. With the slow rolling speed, it was using the main spark table (not idle table), and when the RPM dipped, the timing dropped...
  3. Replies
    310
    Views
    28,380

    That's my thought.

    That's my thought.
  4. Replies
    144
    Views
    9,895

    100%. But why is idle adapt not kicking in to...

    100%. But why is idle adapt not kicking in to save the stall?
  5. Replies
    144
    Views
    9,895

    Plugged in Greg's numbers, took an educated guess...

    Plugged in Greg's numbers, took an educated guess at my scalars for the VE table, and think I got pretty close with STFTs being mostly single-digit. I have some refining to do, but am putting this...
  6. Replies
    144
    Views
    9,895

    Before I dump your data in and begin the...

    Before I dump your data in and begin the re-tuning process, would you recommend swapping to the Bosch injectors (as recommended by FIC) or is there not much difference in reliability to the Deka?
  7. Replies
    9
    Views
    646

    Gotcha, thanks.

    Gotcha, thanks.
  8. Replies
    9
    Views
    646

    Did you mean to post something else? Because that...

    Did you mean to post something else? Because that picture shows exactly what I had.

    This is what I changed them to:
  9. Replies
    20
    Views
    3,471

    Following up after several more logs, and no...

    Following up after several more logs, and no disconnecting issues. One of those was 20 minutes long.
  10. Replies
    9
    Views
    646

    I had lowered the RPM table but I see that was a...

    I had lowered the RPM table but I see that was a bad move and luckily I didn't cause any damage.
    The timing was kept very conservative to try to keep the power close to 600whp since it's a stock...
  11. Replies
    9
    Views
    646

    Boost enrichment PE enabling very late

    Did a highway pull yesterday and was shocked to see that my commanded AFR was still stoich upon full throttle and passing through 100kPa. It remained 13.77 (1.07) until 5200rpm and 8psi of boost. I...
  12. Replies
    20
    Views
    3,471

    Per the suggestion, I removed about 10 channels...

    Per the suggestion, I removed about 10 channels that I wasn't actively using and I have successfully had 2 back-to-back 10-minute logs without disconnecting. Not ready to call it resolved yet, but...
  13. Replies
    144
    Views
    9,895

    I took Ed's advice and put high vacuum on the BOV...

    I took Ed's advice and put high vacuum on the BOV to see if there was any change in manifold pressure, and there was none, so no need to change the spring.

    FWIW, this is the venturi I mentioned...
  14. Replies
    2
    Views
    505

    Not fun!

    Not fun!
  15. Replies
    144
    Views
    9,895

    You must've been talking with my wife. I'm...

    You must've been talking with my wife.



    I'm not against it and with regard to re-doing the VE, I can probably just apply a multiplier to a good portion of the map and get very close. I'll try...
  16. Inconsistent data between PID list and histogram values

    Is this behavior of inconsistent values normal? The number in the PID list on the left does not match what is shown in the histogram value. I highlighted the throttle position, but you can see...
  17. Replies
    2
    Views
    505

    Opening a CSV - No Data

    If a CSV is exported, opened & saved, it does not open back up in VCM Scanner.
    I've found that you need to go into the csv with a text editor and remove all the unnecessary commas, then save it, and...
  18. Replies
    144
    Views
    9,895

    oh, my bad.

    oh, my bad.
  19. Replies
    144
    Views
    9,895

    You're cherry-picking on a log I posted yesterday...

    You're cherry-picking on a log I posted yesterday after severely changing some idle VE regions. Those were only changed to try to chase down the stalls caused by negative STIT. Those cells were put...
  20. Replies
    144
    Views
    9,895

    Are you asking me? Because I honestly don't know...

    Are you asking me? Because I honestly don't know the answer to that question. That's why I'm here.
  21. Replies
    144
    Views
    9,895

    These aren't problems...they're minor quirks. ...

    These aren't problems...they're minor quirks. And I paid him to work a specific portion of the map (see above response).
    Now, if I left the dyno and it was running too rich or too lean and knocking...
  22. Replies
    144
    Views
    9,895

    *here Because he's 90 minutes away and I'm...

    *here

    Because he's 90 minutes away and I'm trying to get advice from a general community to learn and fix this on my own. Is that not the purpose of this forum?

    The individual being super...
  23. Replies
    144
    Views
    9,895

    But don't trust the guy who is highly regarded in...

    But don't trust the guy who is highly regarded in the tuning community with 35-40 years of tuning experience, right?

    One thing that is very evident is that every professional tuner seems to have...
  24. Replies
    5
    Views
    593

    Do you think this is false knock from the very...

    Do you think this is false knock from the very low timing and unburnt fuel? I actually encountered this when I was first getting my base tune up and had timing that was too conservative in...
  25. Replies
    144
    Views
    9,895

    You've given me a couple pointers that I greatly...

    You've given me a couple pointers that I greatly appreciate, but by and large you are a pretty negative person and I am kindly asking that you refrain from responding to my posts (in ALL my threads)...
Results 1 to 25 of 171
Page 1 of 7 1 2 3 4