Search:

Type: Posts; User: FstdodgeKY

Page 1 of 7 1 2 3 4

Search: Search took 0.00 seconds.

  1. TBRtuning will get you in the right direction,...

    TBRtuning will get you in the right direction, but to make adjustments to fueling you have to adjust the injector data pulse width vs airmass. Need to make a histogram logging these parameters...
  2. Replies
    4
    Views
    197

    Cant say for sure as i never tried it but i do...

    Cant say for sure as i never tried it but i do believe you can pull front driveshaft and pull abs fuses also, Not for sure tho, dont these have anti roll over sensors?? i know most have the clock...
  3. are you using ve table??? that would be adjusted...

    are you using ve table??? that would be adjusted there if you are other wise if your ANN on the injector data
  4. adjust your injector data for that cell

    adjust your injector data for that cell
  5. Dont have to turn WOT to 5v just zero out pe and...

    Dont have to turn WOT to 5v just zero out pe and add extra fuel to ve table. The ve table is rough and will need alot of work. Injector data should be easy to find for those injectors
  6. Thread: Ve tuning

    by FstdodgeKY
    Replies
    26
    Views
    1,355

    Im ok with only having the one table, just wanted...

    Im ok with only having the one table, just wanted to make sure that what i was seeing was correct and only using one would be ok.
  7. Thread: Ve tuning

    by FstdodgeKY
    Replies
    26
    Views
    1,355

    But I'm curious as to why tho. We zeroed out the...

    But I'm curious as to why tho. We zeroed out the PE table was all and just used ve for all the fueling.
  8. Thread: Ve tuning

    by FstdodgeKY
    Replies
    26
    Views
    1,355

    So after getting my ve table dialed in and...

    So after getting my ve table dialed in and getting control of the knock I've tried to add some timing into motor. Issue now is the pcm is only using PT timing table and dosent switch to WOT table?? ...
  9. Replies
    0
    Views
    96

    fuel pressure

    what is everyone doing to monitor fuel pressure in the hemi cars?? Can the hellcat pressure sensor be used in our setups??
  10. Replies
    3
    Views
    279

    install the one from the site then update it???

    install the one from the site then update it???
  11. Hp70

    Hp70
  12. What's you WOT pedal voltage set at under power...

    What's you WOT pedal voltage set at under power enrichment
  13. Your pedal voltage tells pcm when to go into PE...

    Your pedal voltage tells pcm when to go into PE from my understanding. you can log your open\closed loop in fuel system in scanner and it will show when it switches.
  14. my car is tuned using only the ve table.. no PE...

    my car is tuned using only the ve table.. no PE applied. I believe this would be a better strategy for you. My car is far from where your at but doing it this way for me is much easier to make...
  15. Replies
    16
    Views
    772

    What other "Tools" would be needed to make this...

    What other "Tools" would be needed to make this work?? I here alot about Alfaobd???? would this be needed?? and would i need to pull the BCM info to see if its in there???
  16. Replies
    16
    Views
    772

    Soooo.. if i could get a tune off say a 1320...

    Soooo.. if i could get a tune off say a 1320 challenger? then maybe i could see if the tables are there for trans brake?? If so would you be able to adapt a pre-2018 pcm to work? The first year...
  17. Thread: Knock...Why

    by FstdodgeKY
    Replies
    3
    Views
    179

    When i had them of for the motor work i checked...

    When i had them of for the motor work i checked them and they all looked good as far as the honeycomb went noW i didn't try to push any air through them... sitting back and thinking now though i...
  18. Thread: Knock...Why

    by FstdodgeKY
    Replies
    3
    Views
    179

    Knock...Why

    SO to the point here.. i'm getting a lot of knock on my new setup and just would like some helpful information, I'm seeing up to 8-10 of knock retard on WOT pulls with the stock sensor turned up...
  19. Replies
    16
    Views
    772

    Homer i have been following along with your...

    Homer i have been following along with your launch control, but it never crossed my mind that we might be able to do the same with the trans brake setting.. This is outside of my abilities but if...
  20. Replies
    1
    Views
    95

    P0125 Disable or fix???

    Hey guys im fighting a P0125 code and looking for suggestions on how to remedy this, The car is on SD with both front and rear O2 sensors off with temp set to 300F, i'm assuming this is why im...
  21. Thread: Ve tuning

    by FstdodgeKY
    Replies
    26
    Views
    1,355

    https://forum.hptuners.com/showthread.php?66353-Do...

    https://forum.hptuners.com/showthread.php?66353-Dodge-tuning-w-ANN-InjPW-v-Fuel-Mass-spark-advance

    Read the above post very good information.
  22. Thread: Ve tuning

    by FstdodgeKY
    Replies
    26
    Views
    1,355

    Thanks guys, after a few revisions this is the...

    Thanks guys, after a few revisions this is the way it has been decided to tune, using the VE tables only and NOT the PE tables. The lean spike i was seeing going into boost is all gone and the...
  23. Replies
    11
    Views
    695

    STFT will always be moving around alot as that...

    STFT will always be moving around alot as that what they do, the weather changes and the stft make quick adjustments based on that information, I only worry about LTFT and try to keep them with + -...
  24. Thread: Ve tuning

    by FstdodgeKY
    Replies
    26
    Views
    1,355

    Still fighting with getting the commanded afr to...

    Still fighting with getting the commanded afr to change. Set FA pedal to 2.0 also tried lower with no real change. FA enrichment rate set to .0200. Also having hard time matching my commanded. I'm...
  25. Thread: Ve tuning

    by FstdodgeKY
    Replies
    26
    Views
    1,355

    So when tuneing VE how do you go about changing...

    So when tuneing VE how do you go about changing commanded afr values. I'm aware on how to get my fueling to my commanded but looking to actually changing my commanded values. Are there multipliers...
Results 1 to 25 of 167
Page 1 of 7 1 2 3 4