Search:

Type: Posts; User: gottogo

Page 1 of 14 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    559
    Views
    189,883

    Sticky: The outer edge.

    The outer edge.
  2. Apparently none. My problem was getting .net to...

    Apparently none. My problem was getting .net to install. If you have it installed you should be good.
  3. Deleted

    Deleted
  4. Deleted

    Deleted
  5. mpvi2?

    mpvi2?
  6. Not me, but I can't imagine it makes a difference.

    Not me, but I can't imagine it makes a difference.
  7. It doesn't take much to run the software. I'm...

    It doesn't take much to run the software.
    I'm running HPT on a 1ghz atom mini laptop. It runs great.
  8. If you do put this in, please give us the ability...

    If you do put this in, please give us the ability to disable it.
  9. Replies
    7
    Views
    509

    Select the last channel in the list then press...

    Select the last channel in the list then press Ctrl+Down arrow, repeatedly.
  10. Care to share your PID?

    Care to share your PID?
  11. Replies
    9
    Views
    273

    I have that problem on a Chrysler. It begins the...

    I have that problem on a Chrysler. It begins the write with an erase, then times out. So I'm kinda dead in the water at that point. :)

    I found that if I disconnect the TCM connector from the ECM...
  12. Try right clicking your tune file icon and where...

    Try right clicking your tune file icon and where it says "Opens With" select Change, then select VCM Editor.

    Hopefully that will fix it.
  13. Thread: Fault Class

    by gottogo
    Replies
    30
    Views
    838

    Yep, found the same list for Fords. No one seems...

    Yep, found the same list for Fords. No one seems to know what they mean, not even HPT support. They suggested I contact a dealer.
  14. Replies
    4
    Views
    512

    I have an HP Mini 10 inch laptop (if you can call...

    I have an HP Mini 10 inch laptop (if you can call it that) with a 1.6GHz Atom CPU that I managed to squeeze Windows 10 on. It surprisingly met the min requirements with 2gigs of ram.

    It runs...
  15. Replies
    8
    Views
    849

    Maybe, I guess. :(

    Maybe, I guess. :(
  16. Replies
    8
    Views
    849

    Dang! Must of stumped the forum.

    Dang! Must of stumped the forum.
  17. Replies
    8
    Views
    849

    Bump again. Anyone?

    Bump again.

    Anyone?
  18. Replies
    8
    Views
    849

    As a matter of fact, so am I.

    As a matter of fact, so am I.
  19. Replies
    4
    Views
    231

    Aw crap. But thanks.

    Aw crap. But thanks.
  20. Replies
    4
    Views
    231

    Table Resolution

    Is it possible to make a table larger to increase its resolution?
  21. Replies
    6
    Views
    1,028

    I agree with 07, BUT! Seeing what other people do...

    I agree with 07, BUT! Seeing what other people do helps. I think a repository is a good idea. With the caveat that you have to personalize them before use.
  22. Replies
    5
    Views
    321

    That's the info I was looking for. Thanks.

    That's the info I was looking for. Thanks.
  23. Replies
    5
    Views
    321

    The fact that a Read results in a single file is...

    The fact that a Read results in a single file is what has me confused. If I make changes to the timing and to the trans, will a Write Calibration to the PCM also write the Trans changes?
  24. Replies
    5
    Views
    321

    Anyone?

    Anyone?
  25. Replies
    5
    Views
    321

    ? on PCM/TCM writes

    The NGC3 controller is a separate PCM and TCM. But when you do a read it creates a single HPT file.

    When you do a write the PCM and TCM are listed separately and the PCM has a Write Calibration...
Results 1 to 25 of 342
Page 1 of 14 1 2 3 4