Search:

Type: Posts; User: richhurley

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. I have the same injectors. The attached file may...

    I have the same injectors. The attached file may help you out.
  2. Replies
    1
    Views
    587

    Try adding 10% to the small and large range...

    Try adding 10% to the small and large range airflow tables.
  3. Replies
    4
    Views
    3,676

    Settings for 3 bar MAP sensor: Map Sensor...

    Settings for 3 bar MAP sensor:

    Map Sensor Linear: 61.85 kPa
    Map Sensor Offset: 6.80 kPa
    Map Sensor Offset: 0.10 V
  4. Replies
    7
    Views
    2,596

    Set Max MAP under engine diags to 300.

    Set Max MAP under engine diags to 300.
  5. Replies
    3
    Views
    1,285

    I am running the same injectors. Start with...

    I am running the same injectors. Start with changing your Inj PW Min to .593.
  6. Replies
    8
    Views
    2,336

    Had the same issue, start by reducing airflow...

    Had the same issue, start by reducing airflow from <= .71V by 10% and see if that helps. Keep reducing by 10% until surging is gone.
  7. Replies
    7
    Views
    2,640

    Went through the same issue and the best way I...

    Went through the same issue and the best way I found to resolve it was airflow. Looking at your airflow tables I would suggest lowering airflow from <= .75V. Start with 10% and keep reducing if you...
  8. Replies
    47
    Views
    15,942

    Here are some things to try: - Disable...

    Here are some things to try:

    - Disable Barometric Pressure Fine Tune
    - Increase Throttle Body Airflow in rows <= .5V (Start with 10% and keep adding until surging subsides).
  9. Check your GS Torque Reduction table (36000). ...

    Check your GS Torque Reduction table (36000). The engine temps are way off:

    Yours:

    *F lb/ft
    406.4 0
    838.4 0
    1270.4 2.95024859710906
    1702.4 3.68781074638633...
  10. Replies
    19
    Views
    18,874

    Replaced mine with OEM sensors.

    Replaced mine with OEM sensors.
  11. One thing to try is increasing the values in the...

    One thing to try is increasing the values in the GS Torque Reduction table.
  12. Replies
    22
    Views
    9,819

    Yes you are making sense. The Airflow table is a...

    Yes you are making sense. The Airflow table is a representation of what the throttle body airflow on a bench. The small table offers more scaling on the smaller throttle movements while the large...
  13. Replies
    22
    Views
    9,819

    I was referring to the Engine -> Idle -> Airflow...

    I was referring to the Engine -> Idle -> Airflow -> Idle Torque Spark/Idle Torque Throttle tables.
  14. Replies
    22
    Views
    9,819

    I had the same issue and at first started working...

    I had the same issue and at first started working with the idle torque tables which helped a bit. The fix for me was putting the idle torque tables back to stock and adjusting the airflow tables.
  15. Replies
    22
    Views
    9,819

    Here are the changes you can try to the airflow...

    Here are the changes you can try to the airflow tables:

    Engine -> Airflow -> Electronic Throttle -> Airflow Multiple rows 0.00-0.90 by 5% (x 1.05).
    Engine -> Airflow -> Electronic Throttle ->...
  16. Replies
    22
    Views
    9,819

    One thing to try is adding more air to the...

    One thing to try is adding more air to the Airflow and Small/Large Range tables . Start with adding 5% to the <1V rows and keeping adding to see if the surging subsides.
  17. You may want to try lowering FA Incr rate and...

    You may want to try lowering FA Incr rate and increasing your FA Decr. Also take look at the PE Aircharge table, it's locks the PE at .0167 across the entire table.
  18. You can give this a try: Engine -> Airflow ->...

    You can give this a try:

    Engine -> Airflow -> General -> Sensed MAP = Enabled
    Barometric Pressure Learning = Disabled
    Pressure Ratio PRatio Max = 2.0
    ...
  19. Try reducing the 8* entries in the Min Spark...

    Try reducing the 8* entries in the Min Spark table to 0* and see if that helps.
  20. Replies
    7
    Views
    4,796

    Have you tried enabling Sensed MAP?

    Have you tried enabling Sensed MAP?
  21. Start with the last two rows of your MBT Spark...

    Start with the last two rows of your MBT Spark table. You have a big drop in maximum spark with just a small change in aircharge. Next look at the PT Spark table, looks like you should smooth...
  22. Anything lose that can me making noise the knock...

    Anything lose that can me making noise the knock sensors are picking up? Knock sensor #1 is showing some high voltage across a large RPM range. Jumps from 1.23V to 3.16V in a fraction of a second,...
  23. A check of your log shows timing at 15* at the...

    A check of your log shows timing at 15* at the time of the throttle blip. The car goes extremely lean as timing is reduced to 5* and bottoms out there. The ECM starts adding fuel to correct the...
  24. Adjustments to your VE tables should address the...

    Adjustments to your VE tables should address the LTFT issue.
  25. I would go even lower, I my cammed 5.7, I will...

    I would go even lower, I my cammed 5.7, I will see timing in the -10 when the PCM is trying to maintain the desired idle. The PCM will pull timing to adjust a high idle, so the minimum table will...
Results 1 to 25 of 45
Page 1 of 2 1 2