Search:

Type: Posts; User: bluecamaroz28

Search: Search took 0.00 seconds.

  1. Replies
    107
    Views
    237,694

    Table is attached for Fan Desired % vs ECT.

    Table is attached for Fan Desired % vs ECT.
  2. Replies
    107
    Views
    237,694

    Just downloaded 3.6 and wanted to adjust fans to...

    Just downloaded 3.6 and wanted to adjust fans to turn on earlier after installing 160 deg thermostat on 2008 Yukon Denali 6.2. The Fans table has only Desired % vs ECT. So, what temp do the fans turn...
  3. Replies
    1
    Views
    2,569

    HP Tuners Software

    Where can I download HP tuners software.

    I could not log in to my customer page. Tried to re-set the pass but it goes to old e-mail that I no longer can access from home.

    I sent an e-mail to...
  4. Replies
    5
    Views
    3,423

    You are right. With help from a member over...

    You are right. With help from a member over LS1TECH, here is what I found.

    I poped the U cover and watched as I open the throttle and it closes except a bit at the end. Forced it by hand to close...
  5. Replies
    5
    Views
    3,423

    Ok. Here is what I found out. TB sticks at...

    Ok. Here is what I found out. TB sticks at partially open. It does not close 100%.

    I foreced it by hand and it would idle perfect. Done this several times and it idles perfect when I force TB by...
  6. Replies
    5
    Views
    3,423

    Anyone, please.

    Anyone, please.
  7. Replies
    5
    Views
    3,423

    High Idle

    It is stock 1999 LS1 Camaro with headers only.

    It started after taking it radiator shop for cleaning the radiator. Rad was removed out of the car and put back after cleaning.

    When started, it...
  8. Replies
    3
    Views
    2,143

    You need to update the fuel injector size for the...

    You need to update the fuel injector size for the larger injectors. Otherwise, you will flood your engine with fuel.

    Read the VCM. Open tune file then go to engine>fuel control>general>flow rate...
  9. Replies
    0
    Views
    1,165

    KR Issues-After Dyno Tune

    I have a knock retard at 3800-5800 special right after a transmission shift.

    I tried and set PE delay to zero and decreased ETC vs PE vs RPM from 90 to 70. It lowered the knock but still there...
  10. Replies
    10
    Views
    6,443

    It didn't yet. I was asked to remove the PCM...

    It didn't yet.

    I was asked to remove the PCM and take shots for the connection plugs and PCM and send it to tech support.

    Have not done that yet.
  11. Replies
    15
    Views
    17,400

    Thanks bro. Pics attached

    Thanks bro.

    Pics attached
  12. Replies
    15
    Views
    17,400

    Tuning Stock 2008 GMC Yukon Denali 6.2

    Trying to tune bone stock 2008 GMC Yukon Denali 6.2. Where to start?

    I have LC1 but didn't set it up yet.
  13. Replies
    3
    Views
    2,892

    Pulled the fuse, it's number 14, and put back. I...

    Pulled the fuse, it's number 14, and put back. I was able to reflash it.

    Piece of cake.

    Thanks.
  14. Replies
    10
    Views
    6,443

    Done and log file sent to [email protected].

    Done and log file sent to [email protected].
  15. Replies
    3
    Views
    2,892

    2008 Yukon Denali Tcm Error

    Done read entire. Then changed speed limiter. Saved changes with new name. Reflashed entire but it is unable to complete and gives this message:

    "TCM was not found. Flash File requires a TCM. Load...
  16. Replies
    10
    Views
    6,443

    Ford Credit with GM VCM Suite

    I have the GM VCM suite with 8 credits. Can I buy credits for Ford? I want to tune 2010 Ford Expedition to remove speed limit.
  17. Replies
    2
    Views
    1,956

    I am getting the same problem. Engine is removed...

    I am getting the same problem. Engine is removed but PCM is untouched with ignition key on and fuse disconnected for fuel pump.

    Car was tuned by a shop using EFI live (MAF Tune). Does that matter?...
  18. Replies
    1
    Views
    1,800

    Scanning fo KNOCK RETARD

    How do I scan for knock retard? Looked in the PID's list but there is no retard only advance.

    How do I add knock retard if it isn't in the list of PID's?:confused:
  19. Replies
    161
    Views
    197,580

    I am new here and just got my MPVI Pro. Looking...

    I am new here and just got my MPVI Pro. Looking for a wide band sensor that will work with MPVI Pro but don't want to buy a complete widband/data logger like LM1.

    What are my options? Any part# is...
Results 1 to 19 of 20