Search:

Okay, I got the histogram made. How do I log the data to calibrate it? Do I save it seperate? I got the standard interface, so I know I need to take my laptop with, but how do I start the logging...

Could someone make me a custom histogram to use for maf calibration. I can't figure out how to do the long term fuel trim vs short term fuel trim vs maf frequency. I think that is what it is to...

My long term fuel trims hangs around -5 and short term fuel trim is around -2

I don't know how to do the histograms. I got a new cold air intake and I appear to be burning more fuel. I have narrow band o2 sensors. When I did a scan of my o2 sensor it appears to be going out...

How do I calibrate the maf, if I have a map sensor as well. I have VE airflow. I don't have the option in hp tuner for dynamic airflow or idle airflow either. I got a cold air intake system...

Okay my hp tuner editor doesn't give me the option for idle airflow tuning or dynamic airflow tuning. It shows MAF Calibration and also Main VE and positive and negative MAF allowed delta airflow. ...

Okay. I just installed a new cold air intake and it seems I'm burning about a 1/16 more gas at lower speeds and even more at higher speeds. I have no idea what to do. I'm new to tuning. Can...

I'm fairly new at this. how do I reset my fuel trims for one and what would be a good adjustment on the maf table for the new intake? Will it cause my car to go real lean and can it overheat?

I just got a new cold air intake for my car and I want to increase my fuel economy the best I can. Does anybody have any ideas on MAF calibration and/or AFR adjustments that I can make to improve my...

My computer crashed on me a while back and I was forced to reformat the computer. I have a 2002 chevy malibu and the tune repository doesn't provide a stock tune for it. The stock tune I had got...

I've been getting a lot of bcm DTC's in the hptuner scanner after reprogramming my Pcm. What can I do to resolve this issue.

I have a 2002 chevy malibu and my fans don't seem to kick on at the right time. I've also got a list of body codes that the hp tuner scanner pulls:

[Unknown] B2575 - (SES)
[Unknown] B2585 - ...

I'm trying to increase my fuel economy on my 2002 chevy malibu. Right now, my AFR is set to 14.7. Is it possible to lower this number and run a little leaner to increase my fuel economy or is there...

I writed the tunes to my pcm, but the engine still seems to run hot. I've got a 180 degree thermostat in my 02 chevy malibu and have programmed the low fan to turn on at 203 degrees and the high fan...

I'm buying a cold air intake for my 2002 chevy malibu. I was wondering how I can tune for better fuel economy with it. Any ideas?

How much hego delay and bias lean would I add typically?

I'm new at tuning and I'm trying to improve my fuel economy. I got a 2002 chevy malibu with a 3.1L V-6 engine in it. I've read the pcm already and I've got the stock tune saved on my pc. I just...

Hi. I'm new to tuning and just got my mpvi today. I'm trying to figure out how to increase my fuel economy by a few miles per gallon or more if possible without having to install a lot of...

I keep getting a "write timed out" message everytime I try to update the firmware. I've been following the instructions to the key and it still isn't working. What should I do?

I just got my interface today and it says to use only a fully charged battery and no additional power source. Does that include the regular a/c power for the laptop as well?

I just received it today and ready to try it out. Thanks everyone.

They did send me the serial number and application key by email though for my item.

Well, they are a reseller for hp tuners. They said they shipped it now and gave me a tracking number a couple of days ago, but it keeps telling me that that got electronic confirmation to pick it...

I just ordered my vcm suite standard yesterday and their order status page still says "to ship" today after their closing hours. It doesn't provide me with a tracking number yet. Anybody know...

You can go to this link to get the latest updates for .net framework 2.0. Remember if you have 64 bit us the 64 bit redistributable. If you have 32 bit use the x86 redistributable.
...