Is the Fuel System Minimum Voltage in the ECM or CCM? Thanks.
Type: Posts; User: jlbjr
Is the Fuel System Minimum Voltage in the ECM or CCM? Thanks.
OK, some people are saying that raising the voltage at the FSMVoltage helps. I saw another post about raising the DC. My pressure is good in Auto shifting. But, manual all the way to redline the fuel...
Hello,
Do you guys up your duty cycle in the very high flow areas of the tune. Stock it's already well past 100% 500-600kpa in the 425lb/hr fuel flow on the chart. I'm trying to get a little more...
No, not a launch control. Just to help bring the power in to full throttle. To help keep the tires from chirping and traction control from flickering in.
Hello,
Do you all ever use the throttle opening at lower to mid RPM's to aid in accelerating? I'm talking 2016 ZO6 Auto with flex fuel., regular tires. It's set 100% now. I see the factory did use...
Really? It?s labeled wastegate dc in the tune. Supercharger?, what?s that? A10, what?s that? I have over 100 different changes/ adjustments on my tune. So I?m doing the work. This sight is no help...
Hello,
At the very top of my run, the boost goes down before I get off the throttle. Maybe this is just a delay in the log, or could the wastegate be opening a little early? I'm logging the boost...
I raised the shift inertia about 1-2-3 in mid/ low torque. 1,800-3,000rpm. Time of shifts are .2 1-2. Then about .125 gears 2-3, 3-4, 4-5. Then up in higher rpm, it?s stock settings. The shifts feel...
Yes, timing down a little. I also did the shift inertia a small amount. It?s 9 in high throttle settings and 1-2 in low areas. Didn?t feel a difference. I feel/ know that GM up?s all the kick in the...
Hello,
I've been messing around with shift timings 1-2, 2-3, 3-4 etc. at low accelerations from a stop light. From zero- 60mph. 3-4, 4-5, 5-6 feel less snappy than 1-2, 2-3.
if I bummped up the...
It?s my sons car. He got a stage one from zzp. Seems good. I logged for a while yesterday. I?m on my phone so can?t post tune file yet. The stock and tuned timing tables are really rough. Craters and...
Why is it so low? 1-2 degrees stock WOT. Also, the stock timing 3D graph looks terrible. Is this correct? 9 degrees timing in the low ranges. 2016 automatic. Thanks
Thanks
Thanks
Hello, on the modifier table, the torque values seem really low for Z06. So I have to edit the torque numbers? Like high of 650ftlbs to 50ftlbs? Thanks
hjtrbo,
What about Control Speed terminate? Ever put that to Immediate? I want the shift a little crisper. Is that the wrong direction? Thanks,
I want to try it. The table is currently all zeros in my car. Thanks.
Hello,
Do you all ever populate that table on C7 ZO6? Leave the Torque Factor 1, then populate lower values in the Modifier Table With like -.10 , -.15 or whatever value. That would be minus 10...
Hello,
Can't find a lot on Speed Control Terminate. I know what it does, but is there long term problems? I do not beat on the car, a few WOT pulls a week. 2016 ZO6.
Who sets their SCT to...
When you guys change the speed control terminate to ?Immediate?, do you leave the torque management stock? Thanks
Hello,
I'm specifically asking if that code at that time would make the throttle begin to close. I've done a ton of pulls to the redline on that tune, and never the throttle reduced. I added flex...
Hello,
Everything was good a couple days ago. When I did a pull, I got a UO42B light and at that specific high rpm the throttle started to close down. The light turns off at lower speeds and rpm....
Thanks Zinc, is zero degrees 8 positive on the table? I think I saw that. Thanks again.
Hello, can someone please tell me what the Cam table?s numbers mean. Retard or Advance? I adjusted my wide open throttle up above 5,500. Pick up a little torque. I retarded I think? Thanks
Is the EOI pid 1/2? It's showing like 260. So, I bring the SOI closer to close the gap and lower the pulse width. How does it do that? It seems like black magic to me. The fuel injectors are totally...