Hey guys,
I?m hoping you can save me from this headache. E38 ecu (2014 camaro w/ ls3 and 6 speed manual) I cannot for the life of me get DFCO to turn off. I?ve tried using the temperature...
Type: Posts; User: tpickrem
Hey guys,
I?m hoping you can save me from this headache. E38 ecu (2014 camaro w/ ls3 and 6 speed manual) I cannot for the life of me get DFCO to turn off. I?ve tried using the temperature...
So to update, I have verified the wiring to the iac is correct and the ecm definitely has the iac drivers.
I can control the iac with the scanner only when the key is on but the engine is off. Is...
The ecm came out of a drive by cable van and i can manually move the iac using the scanner special functions. I?ll double check the ecm to make sure but I?m fairly certain it has drivers
I do have the wires swapped but I?ll triple check they are pinned correctly
Thanks for pointing that out, I had changed that in the subsequent tune but put this one back in and forgot I hadn?t...
Hi guys,
I am working on a 56 cadillac with a 4.8 4l80e combo. The engine is stock except for a holley 300-137 single plane intake and matching 112-588 4 bbl throttle body. the car will start and...
Would I be better off using a truck 6.0L manual tune? Since the camaro is 5.7L?
thanks Ben!
will any red blue ECM work? or am I limited to finding one from a camaro
Good morning everyone,
I am looking for a solution to my problem. I am building an LSA supercharged 6.0L (LQ9) for my 1956 chevy bel air and I am having trouble deciding which way to go. I need to...
ls3 camaro stalls when clutch is pressed. mods are limited to cold air intake. any input is appreciated
tune file: 114124
Thank sir! This was indeed the problem. How do the harnesses get swapped end to end?
bump
Hey guys,
I finally got to start my LS swapped Chevelle. It's a cammed LQ4 (231/235 at 0.050 and .626/.605 lift) with 243 heads milled 0.020" and ported. Victor Jr intake with a holley 4150 style...
is there anything additional that needs to be done to make the computer know its in SD mode? I was reading about people having trouble with first start because the vehicle was trying to start with...
here is the tune file109598
I actually had you look it over a month or two ago but I?ll post it up again! Unfortunately the car itself isn?t quite finished yet so I can?t actually drive it. I don?t plan on dialling the idle in...
Bump
Hey guys,
I?m getting ready to start my 70 Chevelle LS swap for the first time. I?ve done a couple other swaps but nothing where this much has been changed. This car has a different cam, heads,...
How does the computer decide between high and low octane tables? It seemed a little odd to me that they would make the base timing higher than an N/A setup even with the temp tables pulling timing.
Hey guys,
the tune i'm about to post is from a car I'm storing for a buddy of mine. It's a 2014 camaro zl1 with an LSA. I'm new to tuning so I decided to scan his car and see what the tune looked...
thats good to hear!
is there anything else obvious that I'm missing?
So there?s no issues with the data being off by a slight amount? How does the VE table look after the changes?
i'm also going to post the injector data 104388
ok so I tried to input the injector data supplied by deatschworks but every time I put it into the table it changes when I press enter. I also changed the VE table back to stock except I removed some...
hey guys,
I'm relatively new to tuning and I'm working on my first swap. It's a 2005 6.0L going into my 1970 Chevelle.
The engine:
stock bore 6.0L
ported 243 heads milled 0.020 (should be...